Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hello.
I am using nrf51822/SD-130/SDK-12.3 now.
In order to preserve values after reset, no init was set in the IRAM area.
The setting area is Start: 0x20007B80...
Are there any nRF 52805 BLE examples anywhere on the net?
I have not been able to find any. Do they actually want to sell this chip? Do they like money?
Thanks!
Jam...
I am using nRF52810 with SDK 17.0.2 with UART function but I am getting error NRF_BREAKPOINT_COND. I also tried running the uart example of the SDK but the error still occurs...
Hello Nordic Team
I use SDK 15.3. I have an application that is based on ble_app_uart. It switches between uart and beacon advertisement periodically. I used pca10040_ble...
Dear Nordic Team,
i could not find a good and clean starting point for a development of a simple Open Thread application, which is not bases on CLI in the examples. Therefore...
Hi all,
I am now testing with ecdsa example with nrfutil generated key. I found that the public key generated by nrf_crypto_ecc_public_key_from_raw is not the same format...
Hi,
On new fresh delploy of cat Tracker web app, and asset tracker v2 aws without code change (i had a working version a week ago)
Now i have authentication error message...
Hello. I migrated my code from nRF5 SDK for Thread and Zigbee to nRF Connect SDK (NCS) . After that SPI code stopped working :( After debugging with the oscilloscope, I found...
Hi! I am trying to write code on MFRC522 to read data from RFID tags and write data to them, but the datasheet leaves much to be desired, and libraries are available only...
Hi,
I want to upgrate bootloader in my firmware.
IC: nRF52832
SDK: 17.02
I have finished my project, this project include boot + softdevice + app + settings,and...
Hello support team Devzone.
I am new member and i have a nRF51 DK board.
I try to create hex file for my nRF 51 DK board on the website : Mbed Compiler
when compiler...
Hello,
I'm sorry for this question, it can be easy for most of you I guess. I would like to measure the current consumption of the Thingy91, I see in the documentation...
I am running a simple cloud example where I am trying to send a CoAP GET message to coap.me:5683 server over Thread.
I can ping 64:ff9b::0808:0808 and get a response. I...
Hello I want to know what is the command that I must add to the ble_uart code which exists in the SDK library to send hello word using the bleutooth in the nrf UART application...
in \connect SDK\v1.5.0\nrf\samples\bluetooth\peripheral_uart,data number is limited 20 bytes, more than 20bytes BLE will part data in two or more packs to send or receive...
