Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
I'm seeing duplicate data packets while analyzing our sniffer trace from NRF5340 to iOS app. However, there is no packet loss or any impact on data rate.
What might be the...
Board: nrf5340dk (build board: nrf5340dk_nrf5340_cpuapp) / SDK: v0.16.8 / I'm a complete beginner who touches the nrf board for the first time My Project: max30101 --(measured...
Hello
we have some own created UART drivers which access the UART registers directly.
Those drivers have been working withe the older chip revisions for years.
Currently...
Hi,
I cannot resolve the problem while setting up modem trace RTT logging. I'm also unable to find up-to-date information on how to set this up.
I have connected DK as...
I'm close but this is not working for me yet. I'm trying to send a few hundred bytes from android to my nrf device. So I tried to implement long write where you set prepare...
Hi I've a side request, into the exercise I've to perform some changing into the DK programming interface through the JLink, so the question is how to restore the predefinite...
I am getting an fs_close() -5 error (-EIO) when I write to an SD card using fatfs. I determined this error was associated with FR_DISK_ERR in fat_fs.c.
Additional info ...
Hi,nordic team，
im use nrf52840 develop my product with sdk ncs 2.6.the speed of desktop dfu is so slow,and the speed of configurator channel is also slow.i want to transfer...
Hello. I am facing an issue in configuring ADC for multichannels. I was looking at the Nordic fundamentals course Lesson 6 Exercise 2 .In this example, the adc is configured...
I was working through Nordic Intermediate course lesson 8 exercise 2 - DFU over USB, adding external flash and custom keys. I was using an nRF5280DK. (Sticker: PCA10056 2...
I have been trying to implement a DFU OTA using Bluetooth Low Energy from one nRF52840 DK to another nRF52840 DK using the smp_client_ble ( https://github.com/hellesvik-nordic...
hello.
I am using nRF52820 and nRF5 SDK (17.1.0).
When the fds_gc() function is executed, all bonding information in the pairing area (flash) is erased.
My understanding...
I'm using CYCCNT to time code. Works fine until APPROTECT is set, then after reboot the CYCCNT is always 0. Is there a way to enable CYCCNT when APPROTECT is set?
I'm using...
Hi everyone!
Setup:
Currently, I am using the nRF52840 DK board to evaluate neural network models directly on the nRF microcontroller. To measure the power consumption...
