I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
I'm using the nRF51822 eval kit
I have installed MCP but after starting I get pop-up: Master Control Panel has stopped working
In nRFgo Studio / Device manager pane...
the proximity example is running ok. but when I modify the length of the alert_level I have the following error on the server side that I am not understanding.
476;16:12...
Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
I had one nRF54l15-DK,and I want to make a music player by nRF54l15's BLE,but I am not sure is it supposted LE audio to client my headphone.if it supposted, is it full LE...
I am new to nrf52832 development. The question is that:
I want to do m ultichannel(4 or 5 channels) ADC in scan mode every 1s. and the MCU consumes ultra low current(3-5uA...
As the subject suggests. It is a simple question. I only see development boards with NRF53, but we decided to go with NRF54 in this project. We need BLE and WiFi on the device...
I am trying to retrieve the PIN / HWID required for nRF Cloud onboarding using the AT command AT%XDEVICEID , but I am unable to get a valid response from the modem.
However...
Hello,
NB-IoT RRC Connection Re-establishment is supposedly available on nRF9161/51. Is there a related AT-command to enable / disable?
Best regards,
François.
Hi all,
I am using a tagconnect cable to flash my custom boards using a devkit. I was able to flash 4/5 boards. I first recovered the locked factory boards, and then flashed...
Hello ! I would like to know if the nrf52840 is affected by the errata https://infocenter.nordicsemi.com/topic/errata_nRF52832_Rev2/ERR/nRF52832/Rev2/latest/anomaly_832_149...
Hello,
I am working with the nRF9151 DK and NCS v3.3.0 . I am experiencing a critical modem fault at startup.
Problem Summary: When I start debugging, I immediately get...
I attempted to conduct Bluetooth development using the nRF52840DK (NCS 3.2.0), but I encountered an MPSL error:
ASSERTION FAIL [0] @ WEST_TOPDIR/nrf/subsys/mpsl/init/mpsl_init...
Hello,
I am trying to add different ConcentrationMeasurement cluster types to my application (CarbonDioxide, VOC, Pm1, etc.) but have an issue with zap-gui not saving the...
Good day,
I have been making use of the nRF54LM20A SoC with ncs v3.2.0. I am currently trying to use the high-speed SPI (SPIM00) lines on Port 2 to communicate with an SD...
After installing nrfutil-ble-sniffer v0.19.0 (released 2026-04-30) and running bootstrap, Wireshark does not show the "nRF Sniffer for Bluetooth LE" capture interface. The...
