The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi All
I am doing a BLE based project using nRF51822.Where i need to handle the message [with UUID] by using ble_gatts_char_handles_t.
so, can any one please share information...
I have a central application and peripheral application that are based on the multilink-central/multilink-peripheral examples.
I've modified them to run on the PCA10001...
Hi All,
I'm using nRF24L01P for TX device and want to receive packet from nRF51822 RX device.
nRF24L01P TX device Register settings are as follows;
Reg.EN_AA=0x00...
I am trying to develop for some nRF51822 mbed boards, and I would like to use the S130 SD to enable both central and peripheral behaviour. The machine I'm using for development...
Hello Team,
We are using custom nRF52833 with nRF21540 (PCB). we manually controlling the nRF21540 FEM using GPIO and SPI (not using the FEM driver) for testing purpose...
Hello
On my application I have noticed that when I use hardware flow control of the uart1 (not the console uart) the processor will get stuck just before the application...
I want to use a hardware encoder to implement a mouse scroll wheel. Do you provide a QEDC routine for me to quickly learn and use? Are there any specific pin requirements...
I've had problems during installation probably due to firewall/proxy/network protection, so I managed to install from command line as specified in Installing the nRF Connect...
I have a couple of questions regarding the operation of the nPM2100 when using the LDO in Ultra-Low Power (ULP) mode, both in active and hibernate states.
Active Mode...
I used the Nordic plugin in VS code to open the process very slowly, and the build is also very slow, it takes a few hours, I have reinstalled VS code, I have also re-downloaded...
When configuring the Bluetooth protocol for NRF5340-CLLA, should I use nrf5340dk/nrf5340/cpuapp/ns or nrf5340dk/nrf5340/cpunet when adding the build configuration, or do I...
When using the nrf52832 to scan and connect to a BLE central device, the first connection is successful. However, after the first connection is disconnected and I attempt...
Hi,
We’re developing a BLE-based product on the nRF54L15 (InsightSIP ISP2454-LX) using nRF Connect SDK v3.0.2 , with MCUboot enabled for DFU.
Our BLE application is based...
I have a custom board using a nrf5340 and am getting a 1 when trying schedule delayble work and I can't figure out why. I isolated the code to test which gets called from...
I recently updated VS Code and regret doing so. My SDK 2.3.0 was working fine for over a year. But VS Code keeps prompting me with an update. I finally updated it and I can...
I want to use the async driver,but did not find the example or explanation.
I have looked for the whole examples with "nrf_libuarte_async.h", found nothing,a little strange...
Hi, The latest version of the NRF connect VScode extension uses forward slashes in paths, which break pristine build on Windows.
The path to my sources has /V in it which...
I want to control RADIO using the TimeSlot API of nRF54L15. I have already created the code for nRF52. However, it seems that RADIO control of nRF54L15 is slightly different...
