I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
Using VSCode with nRF Connect extension on Ubuntu Linux 22/04 with nRF SDK 3.0.1 and nRF Toolchain 3.0.1 installed I can create a build configuration for Zephyr's hello_world...
Hello, I did my first BLE design and it went wrong I missed some critical design requirements and I want to ensure that the next prototype performs better. The design is a...
We want the system to be in low power mode in idle state. Therefore after advertisement is sent the BLE is switched off using bt_disable. The return for this function is fine...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
Hi All, I am trying to write to "adafruit e-link 2.13 Featherwing colour dispaly" from nRF54L15DK running zephyr. With ESP32 i am able to write to the display. But with nRF54L15DK...
Hi,
i'd like to know if I can use uart1 with non secure build. I have see this doc here , but I have try to add these configuration in my prj.conf:
And add this...
Hi,
I am currently developing an nRF54L15 module.
During the evaluation, I measured the Tx current consumption and got a result that was 2mA higher than the value listed...
Hi.
I've noticed that the Zigbee Add-on R23 has just released version 1.0.0 and is not marked experimental anymore. This is great news.
But I find that the references...
Hello, I'm trying to perform a firmware update using the FOTA feature on the nRF7002. After building and running the firmware update code, the following error occurs:
...
Hi, i am looking for basic start up parameters for a 24L01.
I do all my programm in assembler (sorry i am old).
what i aim to do is simple TX-RX, like a small remote...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
I am using nRF9160 to develop a product for a client that requires displaying the name of the current carrier on the screen. According to the AT instruction manual of the...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
Hi Team,
We are developing on a custom board with an nRF54L15 (Raytac Module with NRF54L15_xxAA_ENGB) and are unable to provision a pre-generated secp256r1 private key into...