nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hi,
i tried to send data from ios 7 via tx_characteristics(like in UART example) but received error:
didWriteValueForCharacteristic 2A38 error = Error Domain=CBErrorDomain...
Folks. I developed my own circuit using nRF 52833 and I`m trying to upload a new firmware via SWD interface. I'm not getting connected to the target for any reason. Is there...
Using SDK 17.0.2 and the nRF52840DK, I am setting up SPIM with a memory IC (not actually hooked up though, just looking at the signals on the oscilloscope). This code is executed...
I'm facing a problem with a product I'm developing. The problematic setup is as follows:
Two nRF52832 peripherals (S132 v6.0.0), each notifying on two characteristics...
Using: Windows Pro 10.0.19041 Build 19041
I'm trying to run Trace Collector for an issue with the nRF9160 and FOTA. I go to run the Trace Collector and it starts, but says...
I am using nRF52832. For reading ADC value for battery level percentage i have used 800k and 1M ressitor value. But while reading ADC Current cosumption is reached to 3 to...
I am trying to copy from this example:
https://github.com/NordicPlayground/nRF52-ADC-examples/tree/master/ble_app_uart__saadc_timer_driven__scan_mode
but I get:
./nrf5_SDK_Current...
Hi,
I'm trying to understand the PSM availability of my local network.
After playing a bit with the RAT and RPTAU values, I found out that using RAT=16~30 secs and RPTAU...
Documentation states that k_fifo_is_empty() returns 0 if data is available in the fifo (which is really implemented using a queue).
I'm receiving some spurious interrupts...
Hi,
In these conditions "custom device connected+bonded and whitelist enabled", when the device scan for beacons it see only the smartphone bonded to the device (don't see...
Hi! Looking at the product specifications V1.1 specifically 5.2.1 Electrical specification, one can see that on Sleep System On, full ram retention wake up on GPIOTE Port...
Hello,
I have following problem.
I use the nRF52840 DK and want to run it in nRF only mode, so I have the minimum power consumption. If I set the DK to low power mode...
Hi,
I encountered fota_evt_handler in azure_iot_hub.c is missing the call to azure_iot_hub_notify_event for the AZURE_FOTA_EVT_ERROR case, resulting in the application not...
I'm currently working with the MX25R6435F flash chip on board the nRF52840 DK and I'm running into issues with it. I don't know whether it's down to my lack of understanding...
