Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
I am using SDK 17.0.2 and want to use Memory Manager Diagnostics .
I have added to my project's sdk_config.h the following :
#ifndef MEM_MANAGER_ENABLE_DIAGNOSTICS...
Hello community,
I have been working on nRF BLE module. I want to make a project that has a small relay control for an appliance. The device will be connected to a mobile...
Hello guys, the USB controller of nRF5340 requires a voltage on VBUS pin.
1. Can nRF5340 be damaged if VBUS voltage rises into its valid range while the device OFF (VDD...
Hi,
I am using NRF52840 development kit and using s140 softdevice for bluetooth services. When I load the softdevice hex file and later load the Firmware hex file, I am...
Hi,
Currently I am experiencing some issues regarding flashing the modem firmware on the NRF9160. My end goal is to automate the process of flashing both modem firmware...
I am using SDK v12.3.0 for nrf 51822 chip. I am working on hrs example with some custom modifications, so i need to to update application through OTA, i have used bootloader...
Heija Guys,
I have a problem with my PWM. I started with the zephyr version 2.4.99 and switched, after we discovered a bug (Link to ticket: https://devzone.nordicsemi.com...
Good Afternoon, Im using a samsung galaxy tab a - Model num SM-T510 Android Version 10 nRF Mesh app version - 3.1.5
After provisioning 14 nodes, whenever i try to reset...
Hi,
I am trying to integrate UART and DFU serial from the mesh example.
What I did is:
1. Adding uart drivers and libraries into the DFU project.
2. Adding codes...
Hi,
We are seeing the issue mentioned in https://devzone.nordicsemi.com/f/nordic-q-a/20291/offset-in-saadc-samples-with-easy-dma-and-ble/79053#79053 . We have 2 sensors...
Hello, I'm getting started with FreeRTOS in Nordic SDK 15.3 I have created a small test code, using binary Semaphore from FreeRTOS, that waits signal from SAADC callback....
Hi, I want to do some modification in the existing nrf connect sdk sample projects. I did some modification in prj.conf and CMakeLists.txt file. But now I am not able to load...
Hello,
Could please someone suggest to me the 10 POS debugging header(5*2) with 1.27mm with a lesser size footprint?
I need a lesser pad size so I could place it on my...
