Hi,
I'm migrating from SoftDevice 6.0 to SoftDevice 7.0 and I'm trying to implement the DFU in SDK6.0. I am experiencing an issue where whenever the DFU begins(reaches 0...
I have already made code of 3 pwm channels using c[0],cc[1],cc[2],cc[3]. I want 4 PWM channels but I dont have more cc registers left so how can i code it. plz help me.
ALso...
Hello, I have purchased this kit on ebay. www.ebay.com/.../301182420397
Can somebody point me to where I can get documentation on this kit, it came in with mostly Chinese...
According to the nRF51 series reference manual.
10.1.2 Debug interface mode
Debug interface mode is initiated by clocking one clock cycle on SWDCLK with SWDIO=1. Due...
Hi,
I was looking at the .map for my project and I noticed that pstorage.c was taking up a bunch of RAM (~600 bytes), which I thought was a lot, so I went into pstrorage_platform...
The document nRF51422_Evaluation_Kit_User_Guide_v2.0.pdf says:
Locate the Heart Rate demo project found in the folder
ARM\Device\Nordic\nrf51422\Board\pca10003\s310\ble_app_hrs...
Using the nRF Beacons app, but cannot see the battery condition of each beacon. Is this already implemented - if so how to turn on? If not how is it implemented?
Hi everyone, In the Power Management example, why the HFCLK still running when the uC is in sleep mode ? I see it in the HFCLK_STAT => State = 1 Shouldn't it be disable to...
Hello,
I have been using nRF development boards for a while, but recently I am currently unable to program my nRF52 development board, due to driver issues. The following...
I am trying to make TWI calls from an APP_TIMER event. However the TWI calls are failing. I can see that the twi message is sent on an oscilloscope, but the function never...
Hi,
I got the same error as the guy in this question: https://devzone.nordicsemi.com/f/nordic-q-a/26041/compiling-error-for-nrf51-development-dongle
I use another example...
Hi, I would like to use a nRF52 demo board, to test nRF BLE with a HX711 and screen. The nRF module is powered 3.3V but the HX711 and the screen are 5V powered. Is the bus...
Hello,
I am in the process of evaluating the '840's BLE and CryptoCell for a low power application. I am using a modified version of the ble_app_template example, with custom...
Hi guys,
I have custom MAC address that saved in the flash. I used the sd_ble_gap_address_set function to change the Mac address to my custom address.. I found out in phone...
Hello,
Is there any option in nrfjprog to force a Segger's JLink to power the target? I am able to turn the power-out feature on using JLinkExe buy I don't whether nrfjprog...
I refer to nRF52810 product specification v1.1 In all reference designs, C6 is N.C.
I would like to know why this is the case?
I would also like to know why it is included...
Hello,
I am using nRF52832 DK for my project which is to receive data from arduino and send it to a smartphone using BLE. My issue is that i make nRF52832 to enter Bootloader...
I have nRF52832 as my development kit. Currently I am testing various ble peripherals i.e Blinky , beacon etc. Now I have to test IR sensor with the Development kit .I aim...
Hello,
I used a the ble_app_template example to set up advertisements on the PCA10040 board and on our custom board. Both boards function and have good signal strength....
I build ADC example from SDK12.3.0 for nRF51822 QFAA chip from source. I used custom board and changed the pin configuration for UART logging in sdk_config.h file.
But unfortunately...
Hi All,
I am performing OTA-DFU - Generating our own packages on my nRF52DK. but when i am trying to generate zip but i am getting some error , below is the screenshot for...
The aQFN app note suggests a fully open paste stencil (opening size = pad size) for the center pad of the aQFN.
Our assembly house is suggesting a windowed paste stencil...
