I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
Hello,
We are working on android UART service and NUS characteristic to receive notification and testing with the custom board with S130 stack acting as a peripheral.
...
Timer_interrupt.txt
Hi all, can anyone please help me in setup up the timer interrupt? I could only see the printing of "Entered 2". Kindly check on the attached text file...
Hi,
I developed a wire-less sensor based on 51822-BLE. I need a batch test method for the product.
My thought about the test is that connect the sensor to phones, and...
Hi support team,
I would like to know if the following behavior is a normal behavior:
My config: NRF51422 AAE0 + S310 V2.0
When I enable some inetrrupt like UART for...
I went through the documentation of nRF51-iOT-SDK v0.8.0 step by step. But
I could not cross-compile and build the kernel with 6LoWPAN on MAC OSX. I do not have a Windows...
I'm updating our bluetooth firmware and boot loader over the air from iOS and android devices. I've modified the nordic supplied update code (IOS-nRF-Toolbox project) to support...
I would like to use functions from components/libraries/mem_manager/mem_manager.c but it doesn't compile because of absense of sdk_config.h header file.
/home/gerbsh/sdk_11...
I'm concentrating on a work about connecting nrf51-dk device in the sensor node end implementing COAP server, ble enabled rapsberrypi and COAP client using Copper.
To check...
The PPI has been configured to transmit a message every time the timer triggers ( every 1ms).
I'm using IAR Embedded Workbench 7.40.3.8938 as my IDE .
When the system...
Hello all,
Our product based on nRF51 is on preproduction stage. We use both 16MHz and 32kHz external crystals.
The question is:
Is there any way to check programatically...
Dear all,
I do have troubles with the bandwidth of the nRF51822 contained in the Adafruit's Bluefruit LE SPI Friend module. The max. throughput I get is 213 B/s. I'm using...
After doing some DFU work - and it all went fine and dandy ...
I would like to go back to the plain old default bootloader that came with my nRF51 board. I don't seen any...
I'm using IAR IDE for the nordic development of NRF51822 (mdbt40). I'm able to run the example project which does not required soft device. Now i wanted to move further with...
Hi,
Is it possible to program the nRF51-Dongle through the usb, to correspond to Bluetooth content to change GPIO state. Then connect the dongle to an external power source...
Greeting , Nordic team , i have some questions about my project.
First , my hardware and software is following:
nrf51422 (pca10028)
SDK 9.0
SoftDevice S110
My project...
