It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
I have a PCB with an nRf51822 @1.8V, using the SDK 10 (no chance to change it).
The PCB itself with everything but the nRF (we did not iron it on purpose to measure consumption...
I have downloaded the motion_driver_6.12 for Nordic Thingy 52 as given in the readme.txt file. And I am using Segger Embedded Studio to build and debug the code. But the IDE...
I am using nrf51822 with PCA 10001, SoftDevice S110 8.0.1. I try to compile the example "ble_app_proximity_s110_pca10028" and after I made a connection the device disconnects...
Has anybody had any experience in programming an nRF beacon kit over the air using the built-in Bluetooth Smart interface in a Windoze 8 laptop? (HP 255 G3) Is this even possible...
Hi,
I wanted to create fixed rate waveform. I first used nrf_delay_us with nrf_gpio_pin_toggle. But I realized it is not accurate enough to do it, especially when the device...
Hello,
I'd like to know how exactly do i implement this function in my app?
I tried getting the value from response (as shown in documentation) : ble_gattc_evt_char_val_by_uuid_read_rsp_t...
Hi,
My Jlink lite CortexM work with nrf51822 DK boards. But my PCB with nrf51822_xxAA chip can't download code. I'm using ukeil
When I chek in utilities Jlink can't recognize...
I am initializing an SPI master to talk to ADXL362 accelerometer using NRF51-DK.
Datasheet page 19: www.analog.com/.../ADXL362.pdf
No matter what I do connected or disconnected...
Hello,
I am new to working with imbedded chips and could use some help. I am working with a pre-programed nRF51822 chip on a PCB and would like to be able to read the imbedded...
Hi I want to using nRF51822 link with MCU ti-am335x have Linux system(Ubuntu) by standard HCI command, BlueZ or related hci tool.
I know that I can use nRF51822 S120 serialization...
I would like to share my wireshark capture file (pcapng) with another developer to view that doesn't have a nordic sniffer. They cannot see the ble protocol information. Is...
I am able to set the connection timeout to 250ms in the ble_app_hrs peripheral sample, but in the ble_app_multilink_peripheral it will not advertise if I set it below 1000ms...
Hello,
When using the bootloader I've noticed that the booatloder resets after advertising for ~1minute. I'm try to figure out if this is intentional.
I notice that...
Hello,
I am currently designing a project that will advertise as two different beacons simultaneously using the Timeslot API. I have successfully implemented the nRF51...
In my all projects, I am using this code to obtain and set local device address:
uint64_t deviceId = ((uint64_t)NRF_FICR->DEVICEID[1] << 32) | ((uint64_t)NRF_FICR->DEVICEID...
Hello,
I build a Broadcaster(iBeacon) with the DK PCA10028. This Broadcaster sends periodically ervery 30ms a message (I have sniffed the Broadcast message and it appears...
