Hi Guys,
since yesterday i am trying to get the DFU with Softdevice S110 (BLE) v7-alpha3 working but haven't succeeded yet. My process is the following:
s110_nrf51822_7...
Hi All,
i would like to know about
1) what is channel in nrf51288?
2) is there any mathematical relationship between channel no and pin no as in ble_app_hrs
example channel...
Hi,
I use UART bootloader SDK example(dfu_dual_bank_hci) to do update firmware on EK PCA10001 board,it can work ok.But i changed the HCI_SLIP_UART_RX_PIN_NUMBER and HCI_SLIP_UART_TX_PIN_NUMBER...
Hi. I have been trying get a notification through ANCS.
I have created an app which is made by modifying ble_app_ancs sample.
It works basically but there is one problem...
Hello,
I'm using the nrf51422 with 210 softdevice.
I'm trying to figure out a way for the receiving slave device to go to sleep when away from the master, but to wake...
To be able to upgrade FW through UART, a bootloader for nrf51822 is required in my project. I have tried out the example bootloader in SDK. But this example is using softdevice...
I followed the forum posts and nan-29 to get eclipse 4.3.2 to successfully connect to JLinkGDBServer via a Segger J-Link EDU on Ubuntu Linux.
I can start the GDB server...
I'm developing an application for a device which needs to support DFU service,
If my device get the specific packet over BLE (like 0xd1), i want to start dfu service. ...
I'm trying to study Message Sequence charts under the BLE GAP (Generic Access Profile) section of the s110 soft device.
However, I've noted that multiple links don't seem...
Hi
I'm studying at university and working on my thesis.
What I'm doing with a remote control and I want to measure the impedance of the antenna, because I want to be documented...
Using: nRF51822-BK-FW (v 1.0.1).
From within, there is the source files for ble_app_beacon_bcs that when compiled/loaded on the beacon hardware, causes the LED to blink...
Hi. I have been trying to follow nAN-29 to migrate from Keil to Eclipse without success. I was excited to find the blog, devzone.nordicsemi.com/.../ . The blog suggests that...
Hi all,
I just had some general questions regarding events and timers on the nRF51822. I'm coming from a Ti CC2540 8051 which used an OSAL system. This made it quite easy...
Hello,
While I was making SPIS part, I got several issues.
I am using STM32L151CB for SPI Master and nRF51822 for SPI Slave.
It seems many people had issues with SPIS...
I've made a modified version of the example DFU provided with SoftDevice v7.0.0-3 alpha that works in single bank mode instead of dual (because I need to bootload a huge app...
Hi all !
I have been working on an nRF51822 based board for a little while, the ten 1st prototypes worked well so we asked our factory to make 20 other with the same design...
Hi All,
Is the lite programmer which comes with the nRF51822 Development Kit sutable to program my code into nRF51822-Beacon?
If yes what cable would I need (supplier...
Hi,
I'd like to read PnP and the system ID from Device Information Service.
How can I initialize system and PnP ID? Are there any examples how to do this for nrf51822...
Hi,
I'm calling sd_ble_gatts_hvx and every once in a while I get an error code of 0x3401. I went through the SDK documentation but I could not find what that error code is...
Hi,
I have a peripheral device that needs to connect to both Android and iOS phones. Depending on which type of phone it connects to it is required to perform different tasks...
Hi
I tried SDK6.0.0 porject at below link.
C:\Keil\ARM\Device\Nordic\nrf51422\Board\nrf6310\s210\ant_bicycle_pwr
According to SDK documentation, we didn't need to modify...
