Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Tuning the nRF24xx matching network:
The balun-function is done by the
180° degrees phase shift in L1. This
causes the signals from the two ANT
pins, 180° out of...
I am sending IMU data as 20 byte packets through nus service at the rate of 50 such packets per second. The device is a nrf51 DK configured as ble peripheral (S110). The application...
Hi all,
I have a makefile which runs perfectly from the command line on Windows under GCC, but in Eclipse it fails with this message in the Console:
make flash
make...
My application had a ID to separate difference device & host for the communication in the same area. When the Host power up, it need to search any existing same ID Host nearby...
Hi ,
I want to set the channels used for exchanging DATA (after connection) when peripheral and master are connected.
i searched and i find that it's like this :
//Set...
Hi I'm using the PCA10003 dev board to try it out the OTA firmware update.
What i did is exactly that:
Modify the bootloader example for S310 softdevice and 10003...
Hi, I have been developing with the nRF52 DK for the past couple of months however I have encountered an issue today which I am unable to resolve.
I am unable to establish...
Continuing my mission to have SES set up to be the complete development environment on a Mac I am struggling to get the Jlink Debugger to behave with SES.
It appears I...
hello , I want to Know how to write value to S0 , L ,S1.
for example : I want Set S0 =1 , L = 16 , S1 = 1 .
but I can't find any register to set S0 , L , and S1. .
My...
We are trying to reduce standby current consumption for our application. When measuring the current depending on the environment temperature we can see a rapid increase of...
My Application will have 4 difference host in the same area, if one device send a data and receive the ACK payload, is it receive all of the 4 hosts ACK payload or one of...
Hello,
I've founded the nrf_drv_lpcomp_init function didn't configure the EXTREFSEL register that why I can't configure the LPCOMP to use the AREF1 pin as an external reference...
Hi all, i have already posted in another discussion my problem, but i will resume it here briefly:
i have a simple program (similar to the tutorial of the custom service...
Hi! I want to send data from the temperature sensor from the beacon, receive them with the nrf51 and then send them to the PC via USB cable. The nrf51 has to start the connection...
Hi!
Is it possible to scan on a single channel using SoftDevice 132 running on nRF52?
If no such functionality exists, is there some workaround? Like timeslot API for...
