Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hi there!
We're designing a system with ~1000 battery-powered moveable devices distributed across a large rectangular area (approx 200m x 1000m) . Each device collects approximately...
I have DevKit board PCA10156 0.9.2. I only see HW files for 0.9.1 on the Dev Kit main page: https://www.nordicsemi.com/Products/Development-hardware/nRF54L15-DK/Hardware-files...
Hi everyone,
I’ve been using the Power Profiler Kit II (PPK2) and was wondering if the firmware source code is publicly available, or if there are any plans to publish it...
Hi everyone,
I'm trying to get the LIS2DH12 sensor sample working with the nRF54L15-DK , but I'm running into an issue where the device doesn't seem to initialize properly...
Hi!
Goal: I want to send as much data as possible using CoAP.
I have connected a nRF52 (IoT-DK) to a Raspberry Pi using BLE and 6LoWPAN. The nRF52 is running the CoAP...
I use the nrf52832 with softdevice S132 s132_nrf52_1.0.0-3.alpha for a ble application.
without the softdevice, the rtos works correctly.
but when I enter this parameters...
I'm moving from nrf51 to a higher performance uC. I think that there is lot of models of nrf52.
what's the reference of the best nrf52 in term of performance. I want to...
I've been using the device firmware update service for quite some time now. I'm looking to add the ble_nus service, but this feature seems to fail when ble_dfus is re-enabled...
With the latest nrfjprog from Nordic and latest J-Link software from Segger, I am still getting the error below.
$ nrfjprog -v
ERROR: JLinkARM DLL version used is too...
I am working on the ble mesh using nrf51822. I am able to read the mesh values using the nrf master control panel android software. But we want to make an android software...
the priority of my custom thread is lowest priority. but it's not possible to call hvx function.
in ble_app_hrs_freertos example,
a sd_ble_gatts_hvx function is called...
Hello,
Suppose I flash a device that uses the nrf52832 with a serial bootloader, SD and valid application, can I still write to UICR regions via a serial connection using...
The nRF UART Android app currently uses a non-monospaced font; so, for example, a '1' is a different width to a 'W'.
This makes it hard to view strings where the fields...
Hi. I'm beginner.
I want to use nRF51822xxAA chip on keil compiler.
project->Option->Target->IROM1 start, Size & IRAM1 start, size.
Please let me know IROM's start and...
Hi,
I'm using ble_app_hids_keyboard example as the base to develop my own application, but was found something really strange, the application seems never get into sleep...
Hello Nordic!
I am using an Android phone and a nRF51822, and I'm performing BLE speed tests.
For these two devices the theoretical maximum is given by 4 * 20 / 0.0075 ...
So I have a remote, a central, and it's connected to my peripheral.
The remote is based on the multilink example.
SDK V11.
I want to press a button on my central and...
