Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hello,
We are currently evaluating a very low power application using the nRF5340+7002. Our hardware design includes a complex power supply configuration, and we need to...
Retrieving Custom Firmware Version from nRF52 BLE Controller to nRF9160 Host
Product: nRF Connect SDK v2.6.0 Hardware: nRF9160 (Host) connected via UART to nRF52832 (Controller...
Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
Hello all,
Our product based on nRF51 is on preproduction stage. We use both 16MHz and 32kHz external crystals.
The question is:
Is there any way to check programatically...
Dear all,
I do have troubles with the bandwidth of the nRF51822 contained in the Adafruit's Bluefruit LE SPI Friend module. The max. throughput I get is 213 B/s. I'm using...
After doing some DFU work - and it all went fine and dandy ...
I would like to go back to the plain old default bootloader that came with my nRF51 board. I don't seen any...
I'm using IAR IDE for the nordic development of NRF51822 (mdbt40). I'm able to run the example project which does not required soft device. Now i wanted to move further with...
Hi,
Is it possible to program the nRF51-Dongle through the usb, to correspond to Bluetooth content to change GPIO state. Then connect the dongle to an external power source...
Greeting , Nordic team , i have some questions about my project.
First , my hardware and software is following:
nrf51422 (pca10028)
SDK 9.0
SoftDevice S110
My project...
Hi,
I am looking for the possibility of getting an unforgeable unique ID of a bonded device within a BLE connection.
Using nRF51422 with SD310 for the peripheral, any...
Hi, could anyone please help me as I currently using nrf51822-arduino-library in a nrf51822 chip and I couldn't call the interrupt function : wakeUp(). Current I'm connect...
hello,
I want to connect Arduino shield with heart-rate sensor to my nRF 51 DK board.
then i have to receive sensor data continually from the sensor.
my plan is transferring...
Hello there,
I'm currently using nrf52832 with s132 and sdk 0.9.2, based on the 'ble_app_uart' example and keil5. I'm concerned about the current consumption because in...
I am working on nrf52 DK board with eclipse gcc + nRF52 SDK 0.9.2. I found the experimental nfc project but it does not include the gcc make file. I would like to ask:
...
Is there any nRF51 SDK example that used OOB authentication? I'll not have any I/0 or display on peripheral side, and my central will be a mobile app, with connection to internet...
Hi,
Need to know the largest amount of power consumption that the Nordic (nrf52) can consume during the highest power bluetooth mode?
Also, what is the largest power...
I am working with the nRF51822 chip and the S110 softdevice on a device that uses an accelerometer to wake up. Battery life is a concern, so we have developed the device so...
Hello, I am encountering with problems with sending 20 bytes of data.
My initial code worked using two timer and I successfully displayed it on an android phone but I wanted...
