Hi Sir,
As we know the nPM2100 support AA/AAA batteries, LiMnO2 coin cells (e.g., CR2032), Alkaline coin cells (e.g., LR44) .
But could nPM2100 support CR123A 1S2P?
...
I've been able to flash consistently but I finally got my nrf5340 custom board working using Hight Voltage DC/DC by setting it to UICR_VREGHVOUT_VREGHVOUT_3V0, but when I...
Hi,
I had a working project for nrf Connect NCS 3.0. I don't know what happened, but now I can't even create a new build configuration. Every time I click on "add build...
Hello,
Please forgive me for this question. I am an extreme noob. And am trying to get started with my first project.
I am working with the nRF52840 DK, and I am trying...
Hi,
I am trying to make the nrf52833 into an Auracast broadcast receiver (for a broadcast from my phone).
I am using bindings to the softdevice controller ( https://github...
Hi Nordic team,
I tried to view logs from my custom nRF54L15-based MCU using J-Link RTT Viewer, but it's (printk) not working. The same prj.conf configuration was previously...
Hello Nordic Support Team,
I am working on an nRF52-based project on a custom PCB using the E73-2G4M08S1C devboard ( https://www.cdebyte.com/products/E73-2G4M08S1C ).
...
Hello Nordic,
I am following example code [--ble-app-lbs-master] for my application in (keil4.6/sdk8.0.0). Its already consisting (app_gpiote), but I want to add some code...
hello,
I am having some doubts regarding the connection handle. Will it be the same for both devices participating in a connection? I was trying to connect two devices, one...
A call to sd_ble_gatts_service_add(..) is returning fault code 0x3001. Looking at the NRF_ERROR #defines, this seems to mean "STK SVC handler is missing".
Can anyone shed...
Dear ladies and gentlemen,
I can't find this information anywhere. In the datasheet on page 519 - 521, I see that the decoupling capacitor C6 on pin 32 (DEC2) is not mounted...
Hi
Currently I have a device with the following details:
Ic Version - 2,
Variant - CE AA ,
Build Code - D0,
Hardware Id - 004d
I am using the softdevice s110_nrf51822_7...
I am trying to set up an environment based on CMSIS Packs. However, when using some components from nRF_Libraries, these lines get added to RTE_Components.h:
#define GPIOTE_CONFIG_NUM_OF_LOW_POWER_EVENTS...
Softdevice Version： 8.0.0
SDK： 9.0.0 IC：
NRF51822 Rev 3
service： NUS ANCS
When the application is not downloaded, the bootloader is working.
After serial bootloader...
I am working on nrf51 iot sdk. I have created a IPv6 tunnel in HE and is able to ping the gateway as follows:
root@raspberrypi:/home/pi# ping6 2001:xxx:18:xxx::1
PING...
Hi,
I already used the sd_ble_uuid_vs_add for adding my base UUID in the internal table and it return a valid uuid_type (in my specific case it's 0x06).
I need to add...
I am using SDK 9.0.0 and i am having a doubt in bsp.h.In this header file when gone through this part of the code
#if (LEDS_NUMBER > 0) && !defined(BSP_SIMPLE)
#define...
For nrf 51 - DK , I flashed s130_nrf51_1.0.0_API
and then using keil uvision I copied over ble_app_uart_s130_pca_10028 and
tried to compile the code,
The code failed...
Hi,
What is the maximum voltage a level than can be given as an input on a pin on nrf51-dk? I've measured VDD at 2.91V. Is it from VDD-0.3 to VDD? If yes, is there a way...
Now I am trying DFU via BLE, some times I can do it successfully and I can do it as long as i want to, but the other time it shows "Error(0x85) GATT error" message and whatever...
