I am working with a custom board based on nrf52833 , SDK 17.1.0 and ble_nus service implemented.
Final goal is to be able to connect to devices only if they provide the...
During my development, I found NRF5 SDK only supports symmetric RX/TX data length settings.
Here is the on_data_length_update_request_evt in nrf_ble_gatt.c file.
static...
Hello,
I am working on a project that will require external flash. Is there an example program compatible with the following external flash device?
M95P08-I - Ultra low...
Hey,
the USB connection to my nRF54L15-DK isn't working anymore.
It is not showing up in nRF Connect Desktop and I can't find it under /dev/tty... or /dev/cu...
The...
I am relatively new to embedded and am wondering if there was a "best practices" guide / checklist for production deployment somewhere. Things like making sure you are using...
Hi. I'm trying to write a simple MQTT app. I am consistently getting these KConfig errors to do with variables I'm not using, and I have tried to set CMake to ignore these...
Good day,
I've developed a board with a MDBT50Q on it. I'm using the Reg0 DC/DC and LDO Mode Disabled reference circuit ( https://www.raytac.com/download/index.php?index_id...
Hi Team Nordic,
Any plans on supporting an official build-setup via Xcode on mac?
Since it's basically more about a way to quickly "git clone" a project + sdk's & softdevice...
I'm trying to upload ble_app_beacon example from SDK 9.0.0 to a beacon board (PCA20006) after successfully uploading it to a DK board (PCA10028).
My first step was to connect...
I have created a customized Services according to nAN36 Document.
SDK using 8.0
Stack S110 8.0
DEV kit PCA10028 nRF51.
J-LInk RTT DEbugger
When the function...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Is there a step-by-step setup for the nrf52 developer kit for Mac (OS X)?
For example, when I connect my DK board, it does NOT appear as a USB drive which is the very first...
I've read through the 'streaming' posts and my need is a little different. I only need about 30 kbps streaming. I've created a service of this but am quite new to BLE and...
Hi all,
Is it possible to check whether there is an active carrier with the nRF24L01+? I've got the TX and RX chips configured via SPI correctly (I think), yet I can't...
What do I need to take care of when I solder CE pin to VCC? (to save I/O)
NRF is mostly in RXing state, and sometimes TXes.
So far I figured out to go from RX->TX mode...
Hi,
Can I use RTT to build a communicate to a command line interface (CLI) in the device?
This would require that the program does not block, as it does in SEGGER_RTT_WaitKey...
I'm using the UART application in nRF Toolbox Version 2.4, iOS 8.4 on an iPhone 5S.
Is it possible to save the logged data to a file, or in any other way get the data out...
Hello,
I am using an Eclipse GCC environment with the following setup:
Ubuntu -> 14.04 (Trusty Tahr)
Eclipse IDE for C/C++ Developers -> Version: Luna Service...
kit: RF51DK.
sdk:nRF51_SDK_8.1.0
SoftDevice:s110_nrf51_8.0.0_softdevice.hex
I want to use 5 channels pwm to control 2 servos and 1 motor;each servo uses 2 channels pwm...
I included the DFU service in my project. With the MCP on my computer it is working fine.
But when I try to perform the DFU over the MCP(v.3.4.1) app on my android device...
I'm migrating firmware from SDK 6.x to 9.0.0
I found pretty many changes in SDK APIs.
Do I have need or do you recommend to upgrade to new SDK ( for bugs / problems...
