I have installed Keil MKD-Lite V 5.10.0.0 and the Segger software (which linked to the Keil IDE). I have tried to install the nRF51 SDK (5 times) and every time iI get the...
Hi,
I am attempting to get the DFU working as per the example provided in the S110 V7.0.0-3 download. I've followed all the steps in the readme in the DFU subfolder and...
Hi all,
I have an application where an nrf24le1 is communicating serially with another processor, using the UART at 57600 bps. I have multiple identical boards communicating...
after flash DFU program into pca10001 board, com3 is not accessible,
www.dropbox.com/.../Screenshot 2014-04-26 15.41.47.png
even after I erase all, and re upload soft...
Using S120 V 8.0.0.3 alpha, processing a BLE_GATTC_EVT_READ_RSP,
received 0x16 bytes of data but there is more to read. Next call to
sd_ble_gattc_read using the same connection...
Hello：
Why Bluetooth Go to system-off mode, sd_power_ramon_set can not be stored. In D: \ RAM save nrf51_sdk_v5_2_0_39364 \ nrf51822 \ Board \ nrf6310 \ s110 \ ble_app_rscs...
Hi,
Recently I want to set up a dynamic network that with the node change this position ,the network will change dynamically.But there is the question,with the node's position...
Hi,
I am using ncs 1.0.0 and Modem FW version 1.0.1.
I am using UART 2 and i have kept UART TX and RX port 0.11 and 0.10 in overlay file.
I want to change the port pins...
Hi,
Our team has identified an opportunity that your nRF52832 fits well, I am having a difficult time getting started with your Bluetooth SDK and reaching out for assistance...
Hi,
As simple as the title! I have tried to move my code from sdk v 3.1 to v3.2 but it will not join the network.
Back to basics and using off-the-box ligh switch example...
Hi
I have been working with the nrf52832 breakoutboard from sparks fun and the nrf52 10040 Dev board.
I want to work with SPI communication in order to intergrate an accelerometer...
I'm having an issue with some iPhone11's, where under certain conditions the iPhone11 is sending two consecutive Link Layer requests with a Control Opcode of 0xFF. The SoftDevice...
Using zboss_start_no_autostart() instead of zboss_start() will cause a power consumption of 630uA. I was expecting the device to be sleep and in a very low power mode.. All...
Hi
When I use the nRF5_SDK_15.3.0, the nRF52832 cannot enter low power (about 900uA). The example is file ble_app_blinky.
The main code is as following:
int main(void...
Hello,
I want to blink the LED by pressing button on nRF9160dk. Is there any sample available to start with?
I started with button demo but on button press there is no...
Hello,
I am using SDK 15.2, could someone please tell me the location of pstorage.h file in the folder. (I found pstorage._platform.h but I cannot locate pstorage.h.)
...
Hi nordic,
I am developing with nrf52832, s132,v15.2,0.I am using secure dfu bootloader. But its connecting in nrf_connect app, after connected, i got this below mention...
Hi,
I'm wondering if you will support sending data using control plane (CIoT EPS Optimization using CP) and Non IP Data delivery for CATM . I assume you will do it for...
Hi:
I am running the example program ble_app_att_mtu_throughput on the SDK52 for the NRF58232 and the NRF58340 next.
My question has to do with how to modify the example...
I'm trying to simplify the open_bootloader example from SDK 15.3. I'm getting rid of version, signature and keep only the CRC validation. I'm actually trying to understand...
Device: NRF52832_xxAA Softdevice: S113 v7.0.0
Hello.
Sometimes, during firmware running, I get a fault from Softdevice with pc: 0x0001A990. Could you inform me what causes...
