Hi Guys,
Thanks for your precious time and insight. Let me try to explain what we did,
We have developed a custom board
After assembling the board, we do a bare board...
Hello all, this tutorial goes to a fellow named Emil who helped me with this project.
Number 1_ Make sure you set up the terminal viewer For debugging with real.You need...
Seeing recent response to my original question on multiple chip selects, I've opted to share a modification to spi_master that I've implemented in part to make handling some...
What is the official status of the Softdevice Serialization for S130 in SDK 9? I could see an older answer on how that was removed in SDK 8 but since almost half year has...
Hi
The documentation for the new feature in S110 v8 to change the gatt table size says that to change it the linker configuration needs changing .
This means it is a...
I used to be able to see my development kit in nRFgo studio and flashed S110 onto the chip. Now all I see is: "No boards connected". I am still able to flash programs onto...
Hello,
I have an iOS application communicating with a custom device having a nordic 8001 chip.
They have established a bonded relation. In nRFgo Studio, in Security...
Using latest SDK and toolchain 3.0.1, VSCode and nRF Connection Pack on Windows 11 I nearly never see a working nRF Kconfig GUI - only the first time directly after I had...
Hello everyone,
We are currently working on a custom PCB using the nRF54L15-CAAA.
I am following the steps for setting up a new custom board using the "Create a new...
Hello.
I'm trying to control a GoPro camera via ble. Gopro has documentation that describes the available services and chars, as well as the exchange protocol ( https:/...
As a life-long embedded software engineer I'm used two or three dozen of different setups, SDKs, IDEs - but all had in common I can copy or clone a project, open, build and...
Hello,
I'm trying to use SLM application on ctcc/nrf9161 hardware ( https://github.com/nrfconnect/sdk-zephyr/tree/main/boards/ct/ctcc ) however it seems I'm not able to...
Hello, I wonder if it is possible to run the Thingy91 in MQTT-S with a certificate system to ensure the connection between the broker and the thingy. (CA, device certificate...
Hi Community,
I'm learning the sysbuild stuffs, try to upgrade my code to sdk v2.9.0.
Exercise 2 - Adding custom image - Nordic Developer Academy
I'm using nRF5340DK...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi，
I am looking forward to ncs2.8.0, which was released last Friday. Today I tried nrf54l15 + 2-wire PA but failed to compile successfully.
sdk: ncs2.8.0
project: direct_test_mode...
Dear Sirs, This is about the software maturity levels of the nRF5340 Audio.
According to the page below, the Maturity level is set to ”Experimental” even in the latest SDK...
Nordic TS,
I'm trying to establish a link between two 9151 DK through which I can pass messages. I'm trying to create a setup where DK 1 receives messages using a DECT NR...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
I don't have found CONFIG_OPENTHREAD_FTD feature in the bulb project prj.conf or prj_release.conf file, but I have found that it is enabled in the final .config file within...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello,
I would like to know how to build the aws_iot example without network offloading to the modem. I need to make AWS connections through both the nRF9160’s LTE-M connection...
