Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
Hi,
I would like to test a websocket connection over NB-IOT with the nRF9151DK. I started with the websocket_client example but I have those warnings and errors at startup...
I have flashed the Blinky sample onto an nRF52840DK.
The power consumption is extremely high.
I am using an PPKII to in source mode. It is connected to the External Supply...
Hi,
The Thingy 91 X uses a shared antenna for BLE and Wi-Fi. I can see from the Hardware Guide and the schematics that there are several hardware connections between the...
Hi,
I am working on implementing the BME680 sensor with the nRF5340DK using the I2C protocol. I have successfully obtained the slave device address and the sensor address...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
As part of a university project I am trying to read an analog signal and transmit it at the maximum data rate over ESB. But I cant seem to get above 1700kbps without any of...
In https://docs.nordicsemi.com/bundle/ps_nrf54L15/page/uicr.html#register.BOOTCONF, I can seee that it is possible to apply Read protection to the first x kB of the RRAM by...
i have some bare-metal RF code that runs on my nRF52-DK, which i'm currently porting to my nRF54-DK.... functionally, everthing is working just fine -- the boards can in fact...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
I implemented the function of DFU using NRF SDK 17,Implemented dfu using MCUboot with ncs 2.9.0
Can the dfu of MCUboot in ncs 2.9.0 upgrade the program of nrf sdk 17
I'm hitting a wall with implementing nRF7002 + nRF52840 without Zephyr.
I've worked with nRF52's for about 8 years now and on about 30+ products, all using the original...
Hi, I'm using the nRF52840 DK with SDK 17.0.2.
I've set selective_auto_ack to true , which should allow the use of dynamic ACK (or ACK payload).
I have two types of data...
Trying to get set up with my new PPK2. Installed NRF Connect and JLink on my Win11 system. When I select the device in the Power Profiler software I get an error. Searching...
Hello,
I am trying to download nRF Connect for VS Code extension but the extension is not found. There is just no result when searching for 'nrf connect' or something...
I am using nRF connect SDK v2.9.0 with a custom developed board that looks like this:
I tried the ' Bluetooth LE LED Button service' sample as it's and noticed that...
I have a board with the npm1300 and a nrf58240. I'm trying to read some status registers out of the npm1300 to debug some trouble we are having with it. It doesn't seem to...