Our pcb is used for gps location data. We have a nrf24L01 nordic chip as the micro process or between the gps module and wireless module (2G). Our engineer needs to capture...
Hey folks,
I'm trying to modify the SPI Master loop back example into a 4 line SPI Master_Slave program. Whenever I change the Tx_Buffer_lenght from 10 to lsome other numbers...
Hi.
I am using S130 softdevice version.
Basically, I am using NUS Service and make a my own NUS central service as NUS_C.
It is correctly work at normal state.
When...
Hi All,
Please Reviwe for a attached circuit file(Chip ANT of nRF51822.pdf).
I also attach a datasheet of chip antenna applied for that circuit(SDBTPTR3015 Data Sheet...
to me it made sense that EN_AA settings are controlling the receiving pipes if an ACK has to be sent back upon receiving a valid packet.
then i thought that the settings...
I am using BLE_Gateway example defined in nRF51-ble-bcast-mesh to create an rbc_mesh over 2 nRF51422 devices . For now, I am just testing it out on 2 nRF51422; I will set...
Hello,
I see when you import an example from the pack installer ( for example pwm, ble, timer examples ) it arrives with the misc controls --c99 on by default , so I cannot...
I attempted to create bluetooth central and peripheral apps using two nRF52840 boards that connect to each other and no one else using the device name. I had limited success...
Hi
We are migrating from Segger Embedded Studio (SES) to VS Code for developing in the nordic connect SDK. We are using the RTT logger for debugging our device. In SES you...
Hi nordic:
Project MCU: NRF54L05; Development Platform Version: NCS 2.9.0. The APP occupies 220KB of space. adding MCUBOOT and Create an pm_static.yml file in the project...
Hi everyone, I'm trying to set up a bootloader chain using sysbuild (NSIB → MCUboot → APP) so that MCUboot can act as an upgradable bootloader. I'm working with the nRF54L15...
Hi Team,
We are using nRF9160 MQTT sample code 'mqtt_simple'.
1. What is the maximum payload we can send in one single PUBLISH?
2. I want to send 4KB of data in single...
We are developing a light product that features a built-in button. A single click of this button toggles the light on/off, while a long press adjusts the brightness level...
We are currently using Zigbee Firmware built with nRF Connect SDK v2.7.0 on the nRF5340.
We plan to upgrade the nRF Connect SDK to v2.9.2 and use the Zigbee Firmware built...
I tried flashing my nrf9151 after running the set-up and loading the AT modem. I then tried to reflash the board but get an error. See below:
2025-07-10T12:53:00.281Z INFO...
I'm trying to run Wi-Fi scanning or AP/STA mode examples on the NUCLEO-U575ZI-Q board with the nRF7002EK shield, but I keep getting an "RDSR2 register failed" error. I've...
Hi!
I have been unable to find a single, simple set of instructions for adding MCUboot to a project(toolchain 3.0.0 sdk 3.0.0) that will enable a non-default signing key...
Hello,
I have opened net/udp sample - https://github.com/nrfconnect/sdk-nrf/blob/main/samples/net/udp/src/main.c over here, to try to send UDP over LTE. Unfortunately, looking...
Hi,
We’ve successfully developed our first few custom development boards based on the nRF54H20 MCU, using the Fanstel BM20C module. However, we've discovered that the module...
Hey All
Im working on a new product and its the first time I'm developing around the nrf5340, I'm looking for some guidance around the supply configuration for maximum...
Hi everyone,
just a quick tip that may save you some debugging time when using the nRF Connect SDK Build Configuration Editor in VSCode.
If you explicitly set a Base configuration...
I was doing a demo code to implement a wake up triggered by motion. I was able to make it work with the integrated low power accelerometer on thingy52 but it only worked 1...