Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Hello,
I want to use the bq274xx.c sensor library. The bq274xx battery fuel gauge has an interrupt pin, which would allow to have the CPU idle until something interesting...
Hi there,
I'm using a slightly modified version of coap_client to test out network connectivity with a 1nce SIM card (USA). Essentially, I've modified it from a GET request...
Hello
I'm new with zephyr environment and I want to use littlefs in order to partition an external flash over spi, and to be able to upload file over BLE by using a SMP...
Hi there everyone I am new in nRF development. I was recently trying to add conexio stratus pro but i could not find it in my VS extension. What could be the issue?
I used two development boards with 52840, Two development boards are running 'first' and 'second' in the '\examples\802_15_4\wireless_uart\secure', respectively.
Additionally...
Hi,
I really like the new Zephyr conn_mgr, it is really easy to use, almost UNIX like. I am wondering what is now the best way to control PSM. Will CONFIG_LTE_LINK_CONTROL...
I have a timer int callback like this:
void pwm_all_handler ( nrf_timer_event_t event_type , void * p_context )
{
if ( event_type == NRF_TIMER_EVENT_COMPARE0) {
...
I am trying to external target using the nRF54L15DK and I get the following error.
Error: Failed with exit code 1. Failed to device info one or more devices: * 1057767167...
Hello everyone
I need to install Nrfutil offline, computers may not have access to the internet, i follow this istruction and prepare the offline directori whit the comand...
Hello everyone!
I have a question about flashing firmware to a PCBA with the nRF54 and nRF91, or any dual MCU board in general.
When looking at the Thingy91(x) this...
Hi everyone,
I have a custom board using the NRF9161. Its hardware is loosely based on the design of the Conexio Stratus Pro and I’m using the Stratus board definitions...
Hi Team,
We are using nRF9160 modem and SDK 1.7 version with Segger Embedded Studio.
Using at_client sample code, observations as below.
1. Tried to read APN configuration...
Hi all,
I may have encountered an issue with nrf9151DK board.
When I only set LED1 with dk_set_leds (DK_LED1_MSK) the LED1 and LED2 are both lit.
Setting other leds...
Hi,
Is there a way to reset the uptime after doing a reboot? Rebooting the device by resetting the power does reset the uptime, however we need a way to initiate the reboot...
Hi there,
We have a device that utilizes an NRF52840 chip. Several threads on DevZone - including this one and this one - warn about the dangers of applying voltage to a...
