Hi,
I'm using long write in one characteristic but if I try to configure this characteritic with write authorization (attr_md.wr_auth = 1) it doesn't work. I need to send...
Hi, I disassembled an Acer Mouse and saw a chip named "NRF A 3152c 1517UH". Can anyone identify the chip or provide me with the data sheet for it.
Regards,
Steve
After i asked this question , i changed to use SDK 8.0.0 hrs "s110_for_dfu",
As the same step to try,
i downloaded softdevice(s110) & bootloader(for 8.0.0)
then opened...
Hello All,
I am trying to create multiple threads for an individual tasks. But when I am creating new thread my program is not working and it's going into some infinite...
I have ASUS ZenPad 10 with Android 5.0.2,
BLE device on nRF51, S110 SDK9 with fixed passkey and encrypted characteristics with following settings
#define SEC_PARAM_BOND...
Looking for someone that has previous experience building multi protocol / time slot topologies using a mix of BLE (central+peripheral) & custom Gazell connections running...
Hi.
I have nRF51422 borad and want to flash to nRF51422 with JLink.
I supplied to 3.3V power to board and is connedted SWDIO to p23, SWDCLK to p24. JLink is connected...
Hello,
I am currently working on integrating the ENC28J60 Ethernet module using SEGGER Embedded Studio and nRF5 SDK version 15.0. As part of this project, I would like...
Hello,
We have a fresh install of SDK 3.0.1 (from within VS Code), toolchain 3.0.0. We try to follow the Matter adding cluster tutorial ( https://docs.nordicsemi.com/bundle...
I started to test with NCS 3.0.0. The first surprising topic I found was, that the nRF Connect for Desktop - Toolchain Manager (v1.6.0) doesn't support NCS 3.0.0 other by...
Hello,
Is there documentation, or an example, explaining how to avoid accessing peripherals owned by the SoftDevice controller in an Application?
I found this:
docs...
I'm using nrf52840 dongle. followed setup based on
https://docs.nordicsemi.com/bundle/nrfutil_ble_sniffer_pdf/resource/nRF_Sniffer_BLE_UG_v4.0.0.pdf
https://www.youtube...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
Hi,
The Thingy 91 X uses a shared antenna for BLE and Wi-Fi. I can see from the Hardware Guide and the schematics that there are several hardware connections between the...
Hi,
I am working on implementing the BME680 sensor with the nRF5340DK using the I2C protocol. I have successfully obtained the slave device address and the sensor address...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
As part of a university project I am trying to read an analog signal and transmit it at the maximum data rate over ESB. But I cant seem to get above 1700kbps without any of...
In https://docs.nordicsemi.com/bundle/ps_nrf54L15/page/uicr.html#register.BOOTCONF, I can seee that it is possible to apply Read protection to the first x kB of the RRAM by...
i have some bare-metal RF code that runs on my nRF52-DK, which i'm currently porting to my nRF54-DK.... functionally, everthing is working just fine -- the boards can in fact...
Hi
I am trying to port some PWM code from the NRF54L15 it uses HAL access because i have found it has faster writes which are useful for my application (testing latency...
