Hello everyone,
Currently we're trying to get the full WiFi stack working on nrf7002dk. We decided to look into the power consumption of the DK board itself as a point of...
I'm using 3.0.1 to compile an app for a nrf5340dk. It is building for 2.9.1, but errors on 3.0.1:
Line 51 is the first line of:
I thought that was the node label...
This is the power supply system in the nrf52832 development board. The manual means that when 1 and 2 are not powered, 3 is used for power supply, that is, cr2032 is used...
I have created my own project and board files for the development board I made. I have 3 I2C busses for different power domains, one SPI bus, and UART for debugging, so 5...
Hi,
I'm using the nRF52832 with SDK version 17.0.1.
I've noticed that when the device wakes up from NFC and remains in proximity to the NFC field, it sometimes experiences...
Greetings! I've applied all the optimizations in the books but I cannot get our application to be ~50% of the available flash memory on the NRF52832, currently it is precisely...
We designed a nRF54L15 custom board and now want to add nRF21540 FEM module to our device tree as follows:
/ {
nrf_radio_fem: name_of_fem_node {
compatible = "nordic...
I will attach my main.c and skd_conifg, maybe i'm overseeing something in code. Also i will attach schematics and pcb. I'm aware of RGB led consumption, in reality it's around...
Dear DevZone,
While porting our project from NCS 2.9.1 to NCS 3.0.0, I ran into linker errors when building LVGL. The linker reports that it cannot find functions defined...
How do I map the build codes noted in the Rev Errata to the stamps on our ICs? I have two versions with QFAAAB and QFAABB stamped on them but the documentation says QFAA-B00...
I'm developing my product using NCS. It compiled fine yesterday, but today when I opened VS Code with the nRF Connect extension, it prompted me to install the toolchain. I...
Hi,
We have some GPIO pins where we want to change their configuration during runtime. We want to switch them between input pull down and output. Is this possible?
When...
Hello, I want to disable parts of my RAM to save power. I implemented this in my project based on the System_Off ram retention example. I'm now not sure if RAM retention is...
I noticed that the product information of the nRF54L15 series kit supports 4Mbps, but I'm unsure how to verify it. Are there any relevant examples available? I have currently...
Dear Nordic Support Team,
I am experiencing difficulties flashing firmware to my nRF52832 development board using VSCode with west flash , followed by J-Link...
Hi, We are using nrf Connect SDK 2.4.0 and have been looking through the NIST vulnerabilities databases. One of the vulnerabilities reported with the nrf5340 is a denial of...
Hi,
I am using nrf52832dk board for test nus service with ncs2.9.0, but I am facing some problem with MTU setting.
I found a configuration item "
CONFIG_BT_L2CAP_TX_MTU...
My application is based on the ncs nrf5340_audio application, but my application and hardware target are both out-of-tree and I am using ncs v2.9.0.
I am able to connect...
Hello,
I have a firmware that sends every 15 min a packet to nRFCloud using nrf_cloud_coap_json_message_send().
The code is working great most of the time : hundreds of...
Hi.
We have a device connected to Azure IoT Hub with telemetry interval set to 10 min and on interupt. Tried changing interval to every hour, but then it looses connection...
Hello Team, We are currently using the nRF52833-QDAA-R SoC for our R&D activities and have assembled the board based on Configuration 6 . However, we encountered an issue...
