dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello,
I want to secure a link between 2 NRF51 (man in the middle and privacy with AES).
How to do that ? (I can use a static key in this application)
Most of the...
I want to create a single hex file that I can use to program the SD, DFU, and my application. I know I can use mergehex.exe to merge these files. To make it so that the bootloader...
Can anyone pls explain what is relation between advertising interval and advertising timeout..
Consider now i am setting advertising interval 1 second how i can prove or...
Hi Nordic,
I have got two PCA10028 boards and have a problem starting BLE on both.
I use latest Keil (5.16) and try to start ble_app_uart_s110_pca10028/ble_app_uart_s130_pca10028...
Hi
When implementing some characteristic handling i noticed, that in the newer softdevices the function "sd_ble_gatts_value_set" has changed to the following declaration...
Hi all,
I need to be able to check the matching networks on a design using the nRF51 series chip. My understanding of the procedure is,
Set up the board, enclosure...
I am having a small doubt in example UART Service. while writing characteristics value from master control panel to nrf51 chip, the stack generating BLE_GATTS_EVT_WRITE to...
Hello,there is a way that can automatically confirm receipt of the packet from the server,without to call evrey time sd_ble_gattc_hv_confirm() after each received indication...
Hi,
I'm using 51822 to control GSM module via UART (57600, no flow control).
My device is USB and battery powered.
After I program the chip I HAVE to disconnect all the...
Hi Team Nordic,
Any plans on supporting an official build-setup via Xcode on mac?
Since it's basically more about a way to quickly "git clone" a project + sdk's & softdevice...
I'm trying to upload ble_app_beacon example from SDK 9.0.0 to a beacon board (PCA20006) after successfully uploading it to a DK board (PCA10028).
My first step was to connect...
I have created a customized Services according to nAN36 Document.
SDK using 8.0
Stack S110 8.0
DEV kit PCA10028 nRF51.
J-LInk RTT DEbugger
When the function...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
Is there a step-by-step setup for the nrf52 developer kit for Mac (OS X)?
For example, when I connect my DK board, it does NOT appear as a USB drive which is the very first...
I've read through the 'streaming' posts and my need is a little different. I only need about 30 kbps streaming. I've created a service of this but am quite new to BLE and...
