Hello,
I recently got a BL653 Click Board and am trying to program it. As I do not have a supported MCU for the NECTO Studio IDE (the ClickBoard's manufacturer IDE), I...
I was looking down at the pinout schematic of the nrf52840 aQFN73, in the schematic provided in the data sheet from v1.1 to v1.11 VSS_PA pin is below ANT pin, but once in...
Hi,
I'm looking to use the nrf connect sdk for development that is compatible with the latest zephyr lts. I believe it will be ncs 2.9.2 compatible with zephyr 3.7.99 (3...
I'm still new to this but particularly in regards to battery. I have a custom board with a nrf5340 and have been working on reading the voltage. I used the battery sample...
This is NOT a runtime error it's a compile time error (application). Failing at stage [154/159] Linking C executable zephyr\zephyr_pre0.elf
Having started by following...
Hello,
I am designing a custom PCBA based on the nRF7002DK PCBA and I really need the Fabrication Notes / Drawing that officially went to the fabricator to direct the build...
Hi,
I purchased nRF52 DK 2 PCs. PCB labeled
PCA10040
3.0.4
2024.34
boath board are new and box packed. from first time itself. I am not able to flash the board...
Hi,
Hope you are doing well.
I would like to use eSIM on nRF9151-DK board and an eSIM has been assembled in the board. However, eSIM is not detected.
According to...
Hi
I am using an nRF54L15 and trying to use pins for I2C, but to do this I have to disable the NFC pins.
I did the following:
But that wasn't enough.
I noticed...
Hi team, After executing RRAMC.ERASE.ERASEALL with an external debugger, I was unable to access the CPU (board) after reset. To resolve this issue, I connected the nRF-programmer...
Dear Customer Support,
Wanted to open a case to follow up on this old one Case ID: 335484
I initially looked at the counter alarm under
https://github.com/zephyrproject...
Hello, I would like to ask if the latest SDK version supports power management on the FLPR core of the nRF54L15. According to this article, the power consumption is quite...
hello everyone I have implemented BLE, ADC, RTC, and UART. After that, my power consumption is around 1.31 mA. Can you suggest possible ways to reduce power consumption or...
Hello Nordic team, For the ( POC), I configured ADC channel 1 and interfaced a potentiometer to pin P1.14. The ADC was set up to read the potentiometer's raw value . As part...
I was doing some developement for a custom board on NCS v2.9.1 when i noticed some of the changes i was making in my prj.conf weren't being set in the application. My impression...
Hello Nordic Team,
I am reaching out to ask for some advice and/or guidance on how I may debug code that:
1. Is initialized and runs BEFORE main
2. Is part of the zephyr...
Hello,
we are developing a device which implements BLE hid keyboard. The code is based on the hid keyboard example in the NRF Connect SDK.
The example uses battery service...
Hello,
I am planning on using the WLCSP version of the nRF52840 chip on a PCB design. ( nRF52840 - Bluetooth 5.3 SoC - nordicsemi.com )
Is it possible to program the nRF52840...
I'm attempting to write software onto a newly purchased nRF52840 dongle using nRF Connect for desktop, but I'm unable to do so. My environment is Ubuntu 24.042 LTS. The LED...
Hi,
I am working on a sensor device that requires very accurate timing on the sensing and sensor signal algorithm side. This device needs a low latency and low jitter radio...
Hi, I'm a novice in embedded systems. I have board based on nrf52811 and firmware written for my device but when I received my board from production I could not load firmware...
Hi all,
I'm modifying the Matter Light Bulb example from Nordic's nRF Connect SDK to integrate I2S audio output on the nRF5340 DK. The goal is to play a continuous beep...
