Hi We have an application where we what to read i2c sensor data over the air to an iPhone. We've taken ble_app_uart_S130 project and grafted in some twi_hardware code. There...
I am interested in the S130 ability to hold 3 central -> peripheral links over BLE, and am looking for some evidence that this has been accomplished with extremely low-power...
I'm trying to implement channel scanning in our nrf24lu1p based USB dongle.
I'm following the specs and basically loop though each channel ;
loop
stop listening
set...
Hi,
I am using the NRF8001 in UART mode and attempting to bond with my android device (Lollipop 5.0 Nexus 6).
i am using the nordic arduino sdk which is found here:...
Hi, I'm using the nRF8001 in an application that requires security so bonds to the remote client/central. My device supports firmware upgrades that may involve new nRF8001...
Hello.
Initially when reading the Gazell documentation I didn't think it'd be a problem but now in Keil seeing this has introduced some doubt whether it's a thing:
...
I've experienced some struggles programming for Taiyo Yuden's EYAGJNZXX board. According to the user manual provided its chip is nrf51822 (which supposedly works with s210...
Hello.
I have a question.
I use nrf52 & Keil.
I want to get data from sensors and send it with BLE.
Now, I found sample codes.
It uses UART and sends with BLE.
...
HI,
I want to send an "Echo" command to the nRF8001 using an ATMEGA328. Can some one suggest code for it ? How should the command be coded in a packet ?
Regards
Hey,
currently I use nrf_gpio_pins_set() and and nrf_gpio_pins_clear() from nrf_gpio.h to set and clear specific GPIO ports, respectively. If I want to change the current...
Alright, I have searched high and low and been unable to find a simple answer to this question. It must be possible for the nrf51 to launch Siri on an iPhone, I have seen...
Hi!
I'm doing an Arduino .txt file sending project using the nRF24L01+. But i'm quite a noob in this so i'd like a bit of advice.
I'm using an Arduino Uno, and I made...
Hello,
while reading some nrf5 examples, I've stumbled over a pattern in the examples, where the result code of a function is stored in variable (most of the time named err_code...
Hello Everyone,
I am porting rf receiver example code which are available in another platform.
I have used this rf module : www.amazon.in/.../B00NRQ3BIM
I am attach...
I am using app_timer to measure the time taken to execute a function. I am using ble_app_template code. As mentioned in the documentation, app_timer needs to initialize the...
I am developing an advertise only code.
There is PERIPHERAL_LINK_COUNT macro in ble_app_template that is used by the softdevice to reserve RAM for peripheral link...
I am using:
DK52
SDK 11
Softdevice S132 2.0.0
I have initialized my service as follows:
#define BLE_UUID_BASE_UUID {0x05, 0x00, 0x00, 0x00, 0x00, 0x00...
I migrate a project from keil to IAR, at the moment of bulding im facing this error:
arm_startup_nrf51.s
Error in command line: Invalid argument to option '-D'
Error...
We did initial work on the NRF51DK (PCA_10028).
We are using SDK 12 and ARM-GCC.
We were able to compile and run successfully the experimental_ble_app_blinky and connect...
I'm attempting to make a sense of app_gpiote.c (in SDK 11) to see if it's suitable for my application and I can't find a match between the documentation, the sample code and...
Hi,
I am trying to use app_timer (had this working in isolation like I wanted) and esb (also had this working by itself) in the same binary. They both implement SWI0_IRQHandler...
