Hi all,
I'm working with the nrf51422 and the nrf51822 and I was wondering what the current status of the over the air DFU system is.
I'm using SDK 6.0 and I managed...
nRF24l01+ at a transmitter module one time successful transmission show & after 1 sec failed also . if any doing programming with atmega32 ,please send code for TX & RX ....
Hello,
can the radio notification and radio disable APIs be used to use the radio hardware from the application layer?
Background of my question is, that I have an application...
Hi,
I am using central s120 with peripheral s110. The connection to the peripheral is depending on the name advertised by the peripheral.
When connection is done, the...
Hello,
I am trying to ecrypt some data in order to send some data encrypted in the MINOR and MAJOR adverts of the device.
I used this code to ecrypt the data ( this is...
Hi,
i use anRF51822 with soft device 7.
I run the UART app on my iPhone 4s with ios7 and on the nrf51822 board the ble_app_uart with keil uVision5.
Both devices connected...
Hello,
I upgraded nRFgo Studio software to version 1.17.0. Installation goes OK but the application crashes every time I try to launch it after installation process.. Then...
Dear all,
I have written some code that controls the SPIS and allows it to transfer data as if it were a master. I am generating the SPIS clock from one timer, and I am...
Hi everyone
for my application I must use the Bluegiga dongle like central (PC side) and nRF51822 for peripheral (hardware side).
So I implemented cable replacement app...
I feel stupid asking this question, it should be documented in the standard and the code but I have looked and googled with no luck.
I want to populate the ble_rscs_meas_t...
What are the considerations when choosing between using an external 32.768 kHz oscillator and just using the internal RC oscillator as the low frequency clock source?
Here...
Hi,
Does anyone know if there is windows (8.0) visual c++ command in the BluetoothGatt functions to use the memory request event with S110?
Many Thanks
Hello,
I would like to develop a quick prototype with nRF51/52 however do not have experience in designing apps. I have seen the example apps and was wondering whether...
Hi,
your Central is able to hold 8 connections with peripherals. Perhaps someone is able to explain how more than one connection is handled? If only one Central is connected...
My Project:
I want to control 2 outputs on the nRF51DK from my mobile device(Android & iOS). Its a simple program:
left button is pressed -> PIN 21 High / left button...
Hi ,
I am planning to buy nRF51 USB Dongle(S120 SoftDevice or S130 SoftDevice) to discover BLE devices and to communicate bi-directional. I am planning to develop C# in...
I am using
nrfgo studio ver 1.20.0.2
s132_nrf52_1.0.0-3.alpha_softdevice.hex
nrf52832_xx_aa_s132.hex supplied by Nordic (ble_app_template)
emIDE 2.20
The firmware runs...
Hi,
with the pstorage library, is it possible to store data at a specific flash address?
The background of the question is that I would like to store data in flash, and...
Hi,
I am using PWM for a buzzer. It is working, but the current consumption is always 300uA when PWM is not in use. This minimal current consumption appears right after...
1: my nrf51 SDK board not work , I replace the USB control IC--ATSAM3U1C-AU(the old is ATSAM3U2CA-AU),can you send me the firmwair of JLINK with this IC and the contacted...
Hi Nordic,
I want to know, how the button_push_sequence works on case of handling different events at different button_push sequence like... (--nrf51-ble-app-lbs--)
...
