I purchased a SIM data from ILIAD and I am trying to connect to network, but the AT command AT+CEREG? : +CEREG: 0,4 instead of 0,5 as I expect.
The lte_lc_connect_async...
In order to reduce power consumption , I configured the RX pin of the serial port with an interrupt , and when the device was asleep , it was woken up by an interrupt , and...
Hi I am using an nRF54L15 with an external watch crystal. I have notice that depending on the manufacturer of the crystal I have to use a different internal load capacitor...
i've noticed that the pc-nrfconnect-ppk is written in typescript (with a lot of .tsx files for visual elements)....
my understanding is that at the lowest-level the power...
I am using the `mcumgr` subsys to enable the DFU (Device Firmware Update) capabilities in a custom device that also features a custom (non mcuboot) bootloader. In order to...
Hi !
I have a peripheral that can connect to other nRF52's or a smart phone such as iPhone or android. Is there an easy way to detect a smart phone?
The best I can think...
Is it possible to see LOG_INF() or LOG_ERR() messages from custom board software when the custom board is connected to a nRF52840DK through connector P20? The custom board...
I have an nRF51822 that I would like to be able to issue a soft-reset command under certain circumstances. I'm not using a softdevice in this version of code, so the other...
Hi,
I'm using pstorage, but found some problem. sd_flash_page_erase will not trigger system event after the operation is complete.
In my code, I registered the system...
Are you supposed to be able to nest critical regions using CRITICAL_REGION_ENTER and CRITICAL_REGION_EXIT? Here I mean you have a function which uses a critical region to...
I'm trying to run bootloader from nRF SDKv6 with SDv7 in gcc.
On our custom board, it runs, but does not advertise (sd_ble_gap_adv_start gets called and does not return...
Hi,
I have developed the firmware using nRF51822 Development Kit. I now want to get to put the firmware on nRF51822 chip used in breadboard. I got a smt adapter with nRF51822...
Hi!
When trying to update app using example bootloader for s110, v.7 from nRF Toolbox I get "Device is not supported. Check if it is in the DFU state".
Bootloader is...
Good morning,
In the application I'm developping with nRF51822 anb S110 SoftDevice, the final peripheral product will be installed in a physical non-accessible place. So...
Hello,
I'm working with the example ble_app_multilink_central of S120. In this example, the scan is done correctly in the three channels of advertising?
Thanks!
I have a characteristic which is a long string. I need to be able to read and write it.
Below is the function for writing to start with. Please comment on this function...
It appears version 7.0 of the SoftDevice 110 supports over the air flashing of softdevice/bootloader/application or a zip containing a combination of the three.
Trying...
Hi,
I'm trying to get SPI (master) to work (nRF51822) for communicating with a quadrature counter (LS7366R).
I've read several implementations of SPI master, such as the...
Using:
GCC 4.8
pure-gcc Setup
Sdk 5.2.0
Softdevice 6.0
I execute some code within interrupt context (softdevice handler) and also in main thread.
I need...
Hi,
What's the difference between a 0.9.0 pca10000 firmware and the earlier version (0.8.0)? I noticed that the throughput with 0.9.0 on the same dongle is much less than...
I'm trying to use the TWI master example with the S120 soft device. It looks like there is a known problem trying to get the S110 working with the hardware TWI. It seems the...
Hello.
I want to make flashing of devices for production faster.
So I want to write application together with bootloader via J-Link simultaneously and not via OTA DFU.
...
