Hi,
I bought a new nrf52840 DK board as one ofthe original nrf board of my Qorvo QM33120WDK1 kit ( 2 x nrf52840 DK + QM33120W + QM33110W) J3 connector broke. Out of the...
Howdy!
I am attempting to develop a system using an nRF52840 and an ADS131M04EVM (ADC). Our application requires us to collect data at a high sampling rate (>= 16k SPS...
I have a nrf9160 DK but when upload SLM application to it i can not send AT commands to it over it's usb port but in asset tracker application it works i want to modify SLM...
I am trying to set up UART communication between the nRF9160 and nRF52840 that are found in the Fanstel BLG840XE. Currently I am sending a test string of "abcd" from the nRF52840...
Hello! This is the third time I'm asking something about the same project, but I'm running into problems one after the other.
The current problem is this - the hogp object...
Hello,
I know this question is more related to Zephyr than Nordic, but I wanted to try asking here.
I’m using the SMP service to send files to my device on a LittleFS...
Finally we got our prototype boards and proof of concept firmware code done and we are a bit stuck on the average power consumption over time for the entire sensor that is...
We have hardware that uses the nRF905 transceiver that inputs different addresses into the nRF905 TX messages based on the specific unit (TX_ADDRESS varies based on unit serial...
Hello
We have devices who uses nRF905 for transmissions between them. When we receive messages we use the AM and DR signal to determine if a message is read correctly. The...
GPIOTE gives us 4.
LPCOMP gives us 1.
What else?
I am working on something related with external interrupts.
Doesn't have problem in my project, but I just always...
Hi Guys,
Is there a way with the Keil C Compiler to get an *.LST file or some sort of Assembly output from C source input?
I'm still trying to write some code to drive...
Hi
Now, I am coding SDK5.0.0 keyboard project and almost done. It's Keil C version. Did you have IAR version for reference? Besides, did you know if IAR supports J-Link lite...
Hi,
I just started to interface the lcd display with nrf51822 evaluation board. The display i'm using is, spi compatible, 18" tft (160x130) from tiny lcd. I took spi master...
I would like to know how to implement reset button on nRF51822. Image of schematic would be very useful, but good explanation should be enough. Thank you in advance.
I...
Hello,
I am trying to build the nrf51822/Board/pca10001/s110/ble_app_proximity project, with gcc ...
I have created a makefile based on the button_radio_example makefile...
I would like to know if the Notification/Indication of a Characteristic is enabled. I suppose this data is stored in a CCCD on the stack. I have not found any SVC instruction...
It seems the only way to use the S310 alpha hex on the development kit is to replace the IC on either of these boards; is this correct or is there another way?
Also, the...
Hi,
I am researching BLE product for a similar task (1 central node with 4-6 concurrent slaves). I have looked up other vendors (TI, CSR etc) and come to a conclusion...
After Googling and searching this forum I still don't know if I can make an HID peripheral (a touchpad) for Android that operates over Bluetooth Low Energy, and is accepted...
Over the air downloaded updates are an essential feature for productization. Are there any examples showing how to implement the OAD? Also is it possible to OAD update the...
Hi,
My nRF51822 evaluation board is not working, here i attached the screen shot's of the error messages i used to get on both the nrfgo studio and in keil. Please suggest...
