We are using the development board PCA10040 for implementing a prototype with several GPIO interruptions.
We are trying to use the NFC pins (pin 9 and 10) as pins of GPIO...
Development Software:
nRF5 SDK for Mesh v3.1.0
SEGGER Embedded Studio for ARM v3.50
SoftDevice S140 v6.1.0
Computer Platform:
Windows 10 Professional
Hardware...
Dear,
software/hardware:
nrf52832 mesh sdk v3.1.0
Q1: when friend feature node code can get? now just is bin file.
Q2: mesh has just four feature devices, friend feature...
It seems the LTE-M / NB IoT isn't available Europe-wide yet, and roaming applies country-wise.
Can anybody share his/her experience of using the BLG840F?
thank you.
Hi,
I am trying to build a thread network using a border router nRF52840 with a Raspi3B+ and 2 others end-devices nRF52840 connected on a CPU Ubuntu 16.04 LTS.
I have...
Hi,
I have a nRF52 DK board and I am trying to build a BLE peripheral with both connectable advertisement (custom with my own name and service) and unconnectable advertisement...
Hi,
I'm exploring the hid peripheral example with 52832 Dev Kit and made it working correctly. While, when I was tring to connect to it with nRFConnect, I found that the...
Hello everyone,
We are currently working on a custom PCB using the nRF54L15-CAAA.
I am following the steps for setting up a new custom board using the "Create a new...
Hello.
I'm trying to control a GoPro camera via ble. Gopro has documentation that describes the available services and chars, as well as the exchange protocol ( https:/...
As a life-long embedded software engineer I'm used two or three dozen of different setups, SDKs, IDEs - but all had in common I can copy or clone a project, open, build and...
Hello,
I'm trying to use SLM application on ctcc/nrf9161 hardware ( https://github.com/nrfconnect/sdk-zephyr/tree/main/boards/ct/ctcc ) however it seems I'm not able to...
Hello, I wonder if it is possible to run the Thingy91 in MQTT-S with a certificate system to ensure the connection between the broker and the thingy. (CA, device certificate...
Hi Community,
I'm learning the sysbuild stuffs, try to upgrade my code to sdk v2.9.0.
Exercise 2 - Adding custom image - Nordic Developer Academy
I'm using nRF5340DK...
Hi, i have locked my beacon with the write_lock characteristic and now i want to unlock the beacon with the lock code which is hard coded in my code. but i was unable to do...
Hi，
I am looking forward to ncs2.8.0, which was released last Friday. Today I tried nrf54l15 + 2-wire PA but failed to compile successfully.
sdk: ncs2.8.0
project: direct_test_mode...
Dear Sirs, This is about the software maturity levels of the nRF5340 Audio.
According to the page below, the Maturity level is set to ”Experimental” even in the latest SDK...
Nordic TS,
I'm trying to establish a link between two 9151 DK through which I can pass messages. I'm trying to create a setup where DK 1 receives messages using a DECT NR...
Hi,
I am trying to integrate the nRF5340 Audio application (CIS Unicast Server role with bidirectional streaming enabled) from NCS 2.9.0 into on my custom nRF5340 based...
Hi,
What is the lowest possible current consumption for nrf52840 dongle dev board with zigbee ?
I'm using this for development and i'm getting 20-30uA in idle. Is it possible...
Hello,
I would like to know how to build the aws_iot example without network offloading to the modem. I need to make AWS connections through both the nRF9160’s LTE-M connection...
Hello Nordic team,
I'm developing firmware for a custom board based on the nRF54L15 , where the LEDs are connected to GPIOs on port 2 . These pins do not support hardware...
After an update recently with the nRF Connect for VSCode Extension, it's been unable to find where my nRF Connect SDK is located when choosing a build configuration. It used...
