Hello. I am literally looking at the set_hrm_cccd function in Python used to write data. This is for the S130 heart rate collector example. I understand the sd.ble_gattc_write...
Totally new to Python but managed to get things like pyserial setup and I've been able run the ble sniffer. However that is as far as my Python knowledge extends, so I need...
pstorage_load and pstorage_clear appear to work fine, but whenever I do a pstorage_store the callback function is never called. This happens whether or not the Bluetooth unit...
Our USB keyboard using nrf24lu1p does not work on Mac OS 10.11.
Before Mac OS 10.11, USB keyboard was worked, but on Mac OS 10.11, it does not work.
I think your library...
In my design I need the RX to be standalone , I.E. no controller attached to it , does the programming STORE in the Chip ? If I set it up as a RX and set a specific Ch. Freq...
[Dev Env]
nRF51 DK
IoT SDK 0.8
IoT SoftDevice
[Question]
how i change my ip in ipv6_coap_server example use ipv6_address_set / ipv6_address_remove API.
To...
Hi Guys,
I have a MCU RTOS project. in Hardware board, builtin Nodic BLE chip over UART,RTOS BLE stack works fine.
We also have a MCU RTOS Emulator based on Qemu,we...
Hi guys,
I am working on a nrF52832 project and want to use Segger Embedded Studio since there is a license agreement for nordic based projects.
I am using freertos from...
Is it possible to communicate between 2 Nordic kits at 1 M baud without HW flow control? I came across this post in the forum which states that bytes can be missed when switching...
I am trying to use gcc to compile a c++ code for nRF52. I am using the TWI library and am getting the error below. Can anyone help me rewriting this macro so that it compiles...
Hello All,
I am using 32 pin nRF52810 chipset.
Crystal have two pin and it will work as in sch. (Xin and Xo)
when using Osc (which is an external clock generator) there...
Hello,
I'm trying to create a lightbulb custom HomeKit accessory by referring to the User Guide v1.7.1. I followed the exact same steps as described in the document for...
Hi,
* (i'am using sdk14.2 ans S140 V5.0.2)
i'am trying to inegrate a beacon application to my ble_uart example , so my purpose is to advertise ibeacon pachet format only...
We have some old stock of the nRF51822 pre 2014/8/20. Was there a change to the product around that time that would prevent us from using from using this stock?
Many th...
Hello,
I'm using FreeRTOS on nRF51 and I would like to use task notifications instead of semaphore to simply manage task's syncronization.
To test its operation mode,...
Hi, I just copied the antenna drawing by referencing the PCA10040 v1.1 and checking the white paper (λ/4 printed monopole antenna for 2.45 GHz) .
I didn't have much knowledge...
Hi,
How is the functionality of P0.21 in nRF52832? It is configured as RESET after turning on the device, right? Is there any way to change it in a way that that the chip...
Hello DevZone,
I am using a nRF52840 for project development.
To test SPI setting is correct or not, I am doing the loop-back test, I set the MISO and MOSI PIN according...
Hello,
I try to configure two nrf52832 devices work with payload of 200 bytes (data should be 200 bytes, not the all ble packet).
I took ble_app_uart_c peripheral and...
Hi all,
Using UART is confusing for me because I see various implementations in the documentation. There is a Serial library, then there is the UART driver and HAL. The...
I am trying to use the comparator to wake me up when a potentiometer is moved a certain amount.
Before I sleep I read the ADC value of the comparator and use this to set...
Hi,
I'm trying to set up the connectable/scannable advertising. I took the app_beacon example and changed advertising parameters.
My final set up is:
The ADV_INTERVAl...
