I am using a eeprep tool which can only be used with command prompt. I am struggling with it.
Here is the format to use eeprep tool :-
usage: eeprep [options] <infile...
Description : It is not possible to flash or debug an application with IAR on the Nordic target. This issue is caused by a bad interaction between CMSIS-DAP IF present on...
Hi,
What should i do after i load mesh app in " github.com/.../nRF51-ble-bcast-mesh" adress?i have two board
When i download the app,why doesnt advertising exist.i cant...
hello
i am using the Nrf52dk with Visualgdb.
i try to run the example project (tcp/IP -> client).
i am using the Nrf5 IoT sdk v0.9
Project complied successfully but i...
I'm using an nRF52 (SDK11.0.0, s132) and am able to generate a hex and axf via Keil/uVision. It uploads and works just fine using a Segger J-Link. I want to try some lower...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hello,
I have recently upgraded from v2.9 to v3.0.1 and have noticed that the mesh security has changed from CONFIG_BT_MESH_USES_TINYCRYPT to CONFIG_BT_MESH_USES_MBEDTLS_PSA...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
Hello,
I am currently working on integrating the ENC28J60 Ethernet module using SEGGER Embedded Studio and nRF5 SDK version 15.0. As part of this project, I would like...
Hello,
We have a fresh install of SDK 3.0.1 (from within VS Code), toolchain 3.0.0. We try to follow the Matter adding cluster tutorial ( https://docs.nordicsemi.com/bundle...
I started to test with NCS 3.0.0. The first surprising topic I found was, that the nRF Connect for Desktop - Toolchain Manager (v1.6.0) doesn't support NCS 3.0.0 other by...
Hello,
Is there documentation, or an example, explaining how to avoid accessing peripherals owned by the SoftDevice controller in an Application?
I found this:
docs...
I'm using nrf52840 dongle. followed setup based on
https://docs.nordicsemi.com/bundle/nrfutil_ble_sniffer_pdf/resource/nRF_Sniffer_BLE_UG_v4.0.0.pdf
https://www.youtube...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
Hi,
The Thingy 91 X uses a shared antenna for BLE and Wi-Fi. I can see from the Hardware Guide and the schematics that there are several hardware connections between the...
Hi,
I am working on implementing the BME680 sensor with the nRF5340DK using the I2C protocol. I have successfully obtained the slave device address and the sensor address...
Dear Team,
I am experiencing issues updating the firmware image on my custom board based on the nRF7002, using an external SPI NOR flash ( is25lp064 , 8MB). The board...
Hello, I’m trying to compile code for a u-blox C209 AOA Tag. I installed the nRF Connect Extension Pack and was able to build normally.
After adding some unrelated paths...
As part of a university project I am trying to read an analog signal and transmit it at the maximum data rate over ESB. But I cant seem to get above 1700kbps without any of...
