Hi Nordic,
I am currently writing about the process of performing channel sounding sequentially on three connected devices. However, after the first channel sounding is...
I am using LVGL for simple Eink display UI, and trying to implement a simple if condition to check if the passed string argument is null as below:
If I only have btn1...
Nordic TS,
I've installed and begin to experiment with the DECT NR+ v1.1.1.0 FW. Initially, I'm noticing on obvious difference in the behavior of the dect_hello sample between...
I am trying to use the FIFO from the ADXL362 with in the Thingy:53. As I noticed there is now the Option to use ADXL362_STREAM. I just wanted to use the example from: https...
The specification for the nRF54L15 states that the typical current consumption for I_TIMER3 (TIMER10 running) is 240 mA/milliamps . The other timer values in the table are...
The Nordic Thingy:91X was initially unable to connect using certain SIMs (e.g., Airtel IoT) due to lack of NB-IoT support or no signal.
After switching to a Jio NB-IoT...
Hi to all,
I am trying to do a ZUTH (Zigbee unified test harness) test run, using the Silabs devices as golden devices (as per CSA recommendation) and nRF 52840 dongles...
I am in the process of getting a Nordic Thingy 91 X up and running for an upcoming development project. However, I’m having some problems getting the Thingy to connect to...
Hi,
I started the LBS example on the nRF52DK_52832 kit and connected the PPK2 kit to the P22 pins for measuring power consumption. I am not sure if I did something wrong...
I installed NRF connect I successfully built project when I flash I get success, but actually I can see project is not flashed what and how can I debug that ?
In the old Nordic SDK we had the option of using "high accuracy" interrupts with GPIOTE by using something like NRFX_GPIOTE_CONFIG_IN_SENSE_LOTOHI(true);
Is there a similar...
I'm currently working on a project using the nRF52833 with nRF5 SDK 17.1.0 and SoftDevice S140 v7.2.0 , aiming to run BLE (Peripheral role) and Qorvo DW3000-based UWB communication...
Hello,
I'm having a serious issue with my nRF52840 board. Here’s what I already tried:
What I have done:
Verified working USB cables (data + power).
Installed...
I am trying to run some of the more basic examples included in the nRF Connect SDK on the nRF5340 included in a Thingy:91 X . I have installed the latest version of the nRF...
Hi all,
I've build a custom bord with an nRF9151, I try to connect to aws iot but it's seems it's doesn't work probably cause by bad cert, I got AWS_IOT_EVT_DISCONNECTED...
We have nRF54H20DK (rev. 0.9.1), SDK: v2.9.0-nRF54H20-1 and the same Toolchain, IDE: VSCode + nRF Connect plugin
We need to control the GPIO LEDs from two cores ( P9.00...
Hi Nordic Team,
We are using the MIMXRT1050-EVK as the host and the nRF7002EK as the Wi-Fi module with an SPI connection. However, we are encountering frequent errors that...
Hi Nordic,
We are develop a multiple switch button device based on nRF54L15. We've two issues now while developing.
1. Matter Network Commissioning Issue with nRF54L15...
Hi! I am developing project with nrf connect sdk 2.9.0 on nrf9160 platform. This is multi image project (b0 + mcuboot + tfm + non-secure application). I needed to configure...
Hi, I am seeking assistance with a very weird issue encountered while programming an nRF5340 SoC using a custom debugging-PCB using a SEGGER J-Link EDU debugger.
The debugging...
We are using nRF Connect SDK 2.9.1, Zephyr. The hardware used is a nrf52840dk, rev2.
We have a proprietary protocol that is running concurrently with BLE and uses MPSL API...
Hi All,
Previous last two times I opened my project in VS Code it displayed a deprecation notice complaining about SDK and toolchain versions. My plan was to address it...
