Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I'm studying at university and working on my thesis.
What I'm doing with a remote control and I want to measure the impedance of the antenna, because I want to be documented...
Using: nRF51822-BK-FW (v 1.0.1).
From within, there is the source files for ble_app_beacon_bcs that when compiled/loaded on the beacon hardware, causes the LED to blink...
Hi. I have been trying to follow nAN-29 to migrate from Keil to Eclipse without success. I was excited to find the blog, devzone.nordicsemi.com/.../ . The blog suggests that...
Hi all,
I just had some general questions regarding events and timers on the nRF51822. I'm coming from a Ti CC2540 8051 which used an OSAL system. This made it quite easy...
Hello,
While I was making SPIS part, I got several issues.
I am using STM32L151CB for SPI Master and nRF51822 for SPI Slave.
It seems many people had issues with SPIS...
I've made a modified version of the example DFU provided with SoftDevice v7.0.0-3 alpha that works in single bank mode instead of dual (because I need to bootload a huge app...
Hi all !
I have been working on an nRF51822 based board for a little while, the ten 1st prototypes worked well so we asked our factory to make 20 other with the same design...
Hi All,
Is the lite programmer which comes with the nRF51822 Development Kit sutable to program my code into nRF51822-Beacon?
If yes what cable would I need (supplier...
Hi,
I'd like to read PnP and the system ID from Device Information Service.
How can I initialize system and PnP ID? Are there any examples how to do this for nrf51822...
Hi,
I'm calling sd_ble_gatts_hvx and every once in a while I get an error code of 0x3401. I went through the SDK documentation but I could not find what that error code is...
Hi,
I have a peripheral device that needs to connect to both Android and iOS phones. Depending on which type of phone it connects to it is required to perform different tasks...
Hi
I tried SDK6.0.0 porject at below link.
C:\Keil\ARM\Device\Nordic\nrf51422\Board\nrf6310\s210\ant_bicycle_pwr
According to SDK documentation, we didn't need to modify...
Hello!
I need more battery life and higher resolution in my applications. That's why i need to level down the signal power, if it is possible. Thanks in advance.
