I'm developing with PCA10040 DK(3.0.0 2022.10), the IDE is SES for ARM 5.42a.
The app is normal after download the application. After a reset or power off and restart, the...
Hi,
We have designed a custom nRF52840 development board based on the XIAO nRF52840 reference schematic. We connected a J-Link debugger to the board and are able to successfully...
Please tell me about the Channel Sounding ranging algorithms. The Bluetooth specification does not define the specific ranging algorithms used; instead, individual companies...
Hi,
We have a device using nRF Connect SDK v3.0.2.
The issue is when we try to do FOTA download and we disconnect the WiFi network (power down the router AP) while it...
# nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board -works on DK
## Summary
On a custom nRF54L15 board, the PDM peripheral...
Hi,
I am using nRF54L15-DK board for development and currently I am trying to talk to an external module via SPI (nRF dev board is the master). I have disabled the external...
I am trying to setup SPI00 as SPI slave on nrf54l15 but not work as expected.
My board configure is like
and c program like
The program intends to use nrf54L15...
I am trying to use the Serial Modem Add-On (SM) application with the attached overlay-external-mcu.overlay. When DTR is asserted (active low), the modem stops responding to...
I would like to know the Host subsystem DN/QDID of nRF Connect SDK 3.2.0 for nRF52832. It is not described below. docs.nordicsemi.com/.../ble_qdid_qual_matrix.html
I am working with the nRF54L15 to create a driver for a peripheral which is controlled by two PWM signals.
My driver relies on the Zephyr PWM driver which goes back to your...
HI
How much current dose the individual GPIO pin source/sink for nRF5340 as in the datasheet V1.3 it is mentioned "Added guidance on maximum combined GPIO sink/source current...
Hello,
we want to setup an environment for automated testing of our bluetooth mesh system.
The test system should be able to provision and communicate over a device that...
Hi
If my calculations are correct the NORDIC whitepaper WP008 on PRINTED MONOPOLE ANTENNA for 2.45Ghz the quarter wave length antenna trace is not 92mm
For TOP layer PCB...
Hi,
I was trying to get the NFC Sample programs to work on the nRF52840 DK but the NFC tag is not being read by my phone. The program itself is running (confimed through...
I am working on a school project and need to set up SPI communication between a wiznet,W5500 and the nRF54L15DK. I can build and run my program but I am getting no responce...
During the development of a Matter over Thread product, I encountered the following issue:
After adding two Matter over Thread devices (an OnOff Switch and an OnOff Light...
Hello,
With NCS v 3.2.1, I am working on a BLE application with nRF52840 dongle.
I was trying to add FOTA feature in my application by adding the following line to sysbuild...
I just ordered and opened up the nRF9160 dev kit from Digikey. I was going through the quick start and I named the device and when I went through the verification step, it...
Can you clarify, is it possible for the nPM2100 to set Vout < Vbat I.e. 1.8v out with 3v battery? The behaviour of the EV kit suggests not...
The datasheet isn't really...
We have a Thingy:91 (nRF9160) that we use for various LTE-M / NB-IoT network debugging. Until recently I was able to see both RRC and NAS messages in both " Cellular Monitor...
Hello,
I am developping an application based on ESB protocole using BT840NE module (nrf52840 + nRF21540) SDK 3.2.0.
on the PTX side, I am measuring the current using the...
