I'm trying to get NFC power-up/restart working on nrf54lDK but the call to sys_poweroff() results in: E: ***** BUS FAULT ***** E: Precise data bus error E: BFAR Address: 0x0...
Hi,
We have deployed some devices now, and we see quite some modem faults popping up.
Could you try to give all info on what you know about these faults we have from...
Environment
SoC: nRF54LM20 (DK; silicon reports nRF54LM20B ENGB — also reproduces built for the LM20A target)
nRF Connect SDK: v3.3.0-rc2, west v1.5.0
Bluetooth: SoftDevice...
Hello
We are using nRF5340 as our EVK with a 12 antenna array plate(4x4 with center 4 ones not being there). Our beacon uses nRF52833.
We used Nordic's sample codes- ...
Title: nRF52840 / OpenThread: how to inject custom IEEE 802.15.4 RX frames into the native receive path?
Hi,
I am working on a test setup around nRF52840, OpenThread,...
We are building a line of product to be used in big size building light management and control.
We believe that both the IV values and a huge quantity of SEQ separate counters...
Hi.
The VS code extension Cortex-Debug reports:
' WARNING: Cortex-Debug will deprecate use of GDB version 8. Please upgrade to version 9+ '
The manual installation...
Hello,
Our project based on nRF52840 doesn't work on MacOS after update from SDK 15.0.0 to SDK 17.1.0.
We can't transfer packets over USB because of changes in SDK 17...
Hello,
I'm using the nR5 SDK 17.1.0 and my goal is to implement a TLS client connection between a nRF52840 and an MQTT broker - I have a Wiznet 5500 set up for the TCP stack...
I'm newbie with the nRF environment. I learned how to create a new project in VS Code from SDK samples but now I have two questions:
1 - I want to crate a blank project...
Hi,
My problem is that my relay nodes are in the mesh network, but some of them only connect to the gateway and not to each other. By changing the publish period in the...
Hello,
NCS1.9.1, VSCode, nRF52840,
those uart samples it's not nRF SDK so easy to use.
Is there a simple uart example?
like nRF5_SDK_17.0.2_d674dde\examples\peripheral...
Hello,
I have a NRF5340 DK and I am looking for an BLE Mesh Sensor example like the ones for nrf52 ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/samples...
Hi Everyone,
I'm using nrf52833 controller, nrfconnect sdk v1.7.0 and Vs code to develope.
I'm trying to flash our custom board with Jlink, which I did for over a long...
Hi,
In our current proprietary design, we use bootloader with SPI function to update App. However in our application, we'd like to update proprietary to standard BLE via...
Goal
Hi guys,
is there an option to enable MBEDTLS debugging as with the CONFIG_MBEDTLS_DEBUG_LEVEL =4 for the MBEDTLS_BUILTIN? I am trying to setup a DTLS client based...
hai
i am using nrf5340Dk (pca10095 ) board (nrf connect sdk v1.9.1).
i want to FOTA/DFU through using internet like updatehub, HTTP service.
it is possible?
please...
Hi, I have an arduino device that will be deployed in a room for audio analysis. I want to use another linux device to perform OTA DFU. However, for the past few days I have...
Hi there,
We are running the Serial LTE Modem sample on the nrf9160 DK. We are currently communicating AT commands via the USB cable and VCOM2.
However we would like to...
I have working zigbee switch example for nrf52840 dongle and I want to add print. Am I using correct code changes? please suggest, Thank you.
printk is not giving any printouts...
Hello,
We are developing a feature on our product that allows us to dump data from an external flash memory.
I'm using a custom characteristic with notification to dump...
