Hello!
I think there is a problem in NCS v3.3.0. nRF54L target, sysbuild build with MCUboot and TF-M, partition layout coming from devicetree (SB_CONFIG_PARTITION_MANAGER...
Hi, I'm developing a keyboard-pcb with NRF52840. I'm doing this as a hobby and are not that experienced with integrated circuits. Anyway, I designed and produced a pcb, but...
Hello,
in cases where the LTE signal strength is extremely low, we observed that the LwM2M /4/0/2 RSRP rolls over from -128 to 127. We found that the nRF Connect SDK uses...
As part of the Bluetooth LE course we need to setup and install the nRF BLE sniffer for wireshark. I have followed the explained steps in the course to set up wireshark to...
The at command documentation says that ENVEVAL is only available in system mode 2 (CFUN=2). Is there a reason why the command can't be run in any other mode? For example if...
Hi
The TWI driver has a twi_clear_bus() function but the TWIM does not.
I'm getting an I2C error, and need to do I2C soft reset. I'm doing this manually at moment but...
I recently completed a field-upgrade path from an nRF5 SDK 17.1 application (with the legacy Secure DFU bootloader) to a fresh NCS-based firmware stack, while preserving user...
Hi everybody,
I am with two custom oards that include nrf52840 chip, one acting as central and one as peripheal.
This example is custom to get multilink, for that i save...
Dear team ,
i am working on ble_app_lbs_nus_c project when in this project try to add nrfx_timer.c file
we got an error like this.
Building ‘ble_app_lbs_nus_c_pca10056_s140...
I was reviewing the MNO certifications, and I see that there have been no updates since 1.5.1.
1) Is it acceptable to use 1.6.1 with AT&T?
2) Is certification planned...
Hi, I am trying to update the battery level through an example of the HID keyboard of nrf52832.I'm trying to connect 3.3V battery to SAADC AIN0, but as shown in the picture...
Hi, I have a question about nRF Connect Programmer tool.
[Description]
The device memory layout shows the address range as "0x00000000 - 0x00100000 (size 1048576 bytes...
Hi,
In our application, we are using HID to control mobile phone or PC.When users connected our product, it will automatically connect next time.
But our product is battery...
Hi
I am using Zephyr samples (common with the samples found in NCS) to evaluate the advertisement function of nRF52833DK.
I have run these examples:
Bluetooth: Periodic...
Hi,
After updating the FW as shown on the video, LED3 is NOT blinking, trying to connect (LTE).
If I open the terminal window, select the board, and pressing the Reset...
Hi,
We are using the GPS xample for the nRF9160. and are struggling a little with getting the GPS fix.
$GPGGA,001932.00,,,,,0,,99.99,,M,,M,,*6F $GPGLL,,,,,001932.00...
Hello to all the Nordic Jedi knights!
I have a question regarding the PPK2: Is there a way to disable auto-ranging and manually select the measurement range?
I know that...
Hey,
I have a custom board with nRF52833. Sensor is connected to: P0.11 (pin 19) - SCL P1.08 (pin 17) - SDA
with code below I don't get any `NRF_SUCCESS` back.
I saw...
I'm trying to build a new device that I bit, bang the I/O Also others to just have simple signal controls.
Below is the portion of my dts file. The example here is the onewire...
Hi,
I am using nRF52810 (s112 softdevice) with SDk version "17.0.2".
How do I set BLE advertise in continuous mode(if not connected then advertise continuously until it...
Hi
I am trying to declare a custom cluster in zigbee and enable the reporting for some attributes of the cluster, i followed this post to create the custom cluster devzone...
