I'm pulling my hair out here. Why would syntax errors completely break the toolchain?
Every now and then ill have a syntax error which causes the build to fail, the entire...
Hi, I have test the throughput using two nRF54L15 DKs and make them close to each other.
My result is:
1. My first question would be: the best througput for 2M phy is...
Hi,
We're working on a project using the nRF5340, where we interface an external NAND flash (4096 blocks) to store high-volume sensor data. We are planning to maintain an...
Hi,
We are currently evaluating the NRF9151 for asset tracking using the AT firmware on the NRF9151 evk and an external MCU for the application firmware, emulating the final...
Hello,
We’re Bachelor’s students developing a project to estimate the angle of arrival (AoA) using a BLE antenna array on the nRF52833. Our implementation builds on Zephyr...
Hello team, I am currently working on the distance measurement functionality using the development kit (nRF5340 and SDK: v2.9.0). At present, the distance measurement runs...
Hi,
Right now I'm looking down at the nrf52840 datasheet, because I would like to do a project with such MCU, but I got to the part of the integrated DCDC converters and...
Hi, I'm developing custom board with nrf52832
The problem is that when saadc returns negative value, all values that saadc returns after are max possible values from config...
PLease, could anyone provide me a code exaple on which i can learn how to use sd_flash_write & sd_flash_erease ? I tried to use them but keil give me this : .\_build\nrf51822_xxac...
Hello Dev Zone.
thanks for watching mt ask.
I need help.
I have 2 question.
1. I need use saadc continuous sampling
in SDK example, is it continuous Mode?
...
For RAM locations, I've looked at the getting started guide that discusses using debugging to find the RAM address. https://devzone.nordicsemi.com/nordic/short-range-guides...
I know one of nRF52840 SPI instances supports direct DCX signal drive but I can't seem to find any mention to this feature in nRF52832 so I am assuming none of its instances...
Hi Sir,
As check the ref. schematic of CKAA, the pin count shows 94.
But in the below table shows the pin count is 93
Is there a typo in the datasheet (V1.1)?
...
We are using nrf52832 and S132 Softdevice. The app starts from 0x26000 and we want to change to some other location may be from 0x27000. We could see that SD is using the...
Hello !
is possible turn off my system using sd_power_system_off when the Watch dog is enabled?
After I called sd_power_system_off my device is restarting and initialize...
I can not find where to change the default pins to connect the nrf52840 to the rpi over SPI. The default pins are SPI pin Raspberry Pi pin nRF52833, nRF52840 or nRF52811 pin...
I have begun using V1.2.0
It seems that I'm no longer to enter AT commands.
I've also tried the AT Command sample and get the same issue.
No problem connecting through...
Hello,
I am adapting the 802.15.4 wireless UART example from the nRF5 SDK 15.3 to also make scans and associate with a PAN coordinator. However i am having trouble with...
I have a time-sensitive block of code run purely by the CPU, not within any interrupt handler or peripheral. Part of the execution is getting interrupted, and so what I would...
I am testing DA7212 with my nrf52840 and i have made connections but i am not sure if thats right. Also i am trying to use i2s loopback example from sdk.
i need some gu...
Hi,
I broke power on/off switch in my nRF52 board. I'm an absolute beginner in hardware (I'm iOS developer...) but I managed to start it. It works, but unfortunately, it...
Hi,
I'm using SDK 13.0.0 and Softdevice s140 5.0.0-2alpha on my nrf52840-PDK. I tested the usbd_hid_generic and usbd_audio examples and they work fine, I can see the device...
