I am using nRF Connect SDK 3.4.1 on three nRF54L15 devices:
A ───────── B ───────── C
A–B: A central / CS initiator
B peripheral / CS reflector
B–C: B central / CS initiator...
Hi,
I have been using NRF PPK2 for two months,
today when the device was connected to docking station and only ground to DUT I notised " High current surge in the USB...
Hello,
I cannot download many of the applications offered in the desktop. I am trying to use the evaluation board for the nRF54L15 offered by ezurio (BL54Lu) and cannot...
Hi,
Is there a way to implement overvoltage lockout by sensing VDD using the ADC? Our goal is to claim that we have power regulation so that we can get full modular certification...
Setup
- Programmer: nRF54LM20 DK (PCA10184), debug out header P13 to an external board over a 10-pin ribbon under 10 cm, SWD0_SELECT grounded on the target side. The DK...
I created software and flashed successfully to the nRF54L15-DK. It is to toggle an LED on and off on P2.09.
#include <zephyr/kernel.h>
#include <hal/nrf_gpio.h>
...
I'm trying to establish a data connection from a Linux host through the USB network interface of an nRF93M1-DK.
The modem registers successfully on the cellular network...
Hello, I'm stuck at the build step from teh IoT fundamentals course as when I try to build I get the next error:
It seems that the build needs two (samples/cellular/nrf91_crypto_partitions...
I happened to write some debug log code that broke my Bluetooth. I don't think it should be doing that. When I burrow into the logging, I don't see why this difference is...
We have switched over to the new device tree based partition scheme, and developed custom board files with not-secure variant and mcuboot for ota. OTA was tested using BLE...
Hi, I have a question with regard to the nPM1100 PMIC and entering ship mode (not exiting it).
If I am interpreting the datasheet correctly, the SHPHLD pin must be held...
Hi Nordic,
We are building a custom board using the nRF9151 LACA.
We see a back-powering issue between the GNSS antenna bias rail and VDD_GPIO.
Setup:
VDD_GPIO...
Hi:
I use ncs3.3.0 and nrf54l15dk.
PC BLE pairing nrf54l15dk failed log:
prj.conf
But with BT configuration, turning off ESB related content, it can be paired...
I have a nRF52832 custom board derived from the 52832DK board. All is working perfectly with the exception of the ADC converter. I am only using AIN0 which is on pin 0.02...
Hello,
I am working on a device based on nRF9160, SDK 2.8.0 and modem 1.3.7.
The devices uses nRFCloud CoAP to send messages. For the most part, it's working great....
Hello, I am currently experiencing an issue with the 802154_phy_test example on the nRF54L15-DK board, and I would appreciate your technical support.
[ Environment ]
...
In theory all driver calls are suspect, but for example I see crashes in nrf_802154_buffer_free_raw, at this assert:
This is easily reproducible by running 802154_phy_test...
Hi, I have an Ubuntu 22.04 LTS virtual machine where I installed the version v3.4.0 of all the needed tools and libraries as explained in nrfconnectdocs.nordicsemi.com/.....
Hi,
I am experiencing an issue where SPI read operations fail after upgrading from NCS 3.2.4 to NCS 3.4.0.
Hardware:
Custom board based on nRF52840
ADS1294...
On a custom nRF54L15 (QFAA) board, SERIAL20 and SERIAL21 initialize successfully ( device_is_ready() = true) but drive no pin activity / no bus traffic at all . On the same...
