I was implementing custom services and characteristics(softdevice:s140, ble) on the nrf52840 dongle, however I couldn't get it to work, even though my code seemed correct...
Hi,
I´m working on a Zigbee-based environment sensor. You can find all related files here: https://github.com/Kampi/BeeLight
Now I have the following scenario: the whole...
Does the nrf54l15 have a register to specify the boot area? Similar to the NRF_UICR->NRFFW of nrf52833.Or does the nrf54l15 have to boot from address 0x00000000?
Hello,
I've been going through the BLE fundamentals course and things are going well. I'm using the nRF5340DK board and SDK version 3.0.2
I've gotten to lesson 3, exercise...
Hi,
I am working on the channel sounding feature on the 54l15 and I want to perform it sequentially between 3 reflectors and one initiator. I realized that after I make...
Hi,
We're at a point in our project where we're working through some regulatory testing for ETSI/FCC certifications with our BLE dongle board (nRF52840 + nRF21540 FEM...
Hi,
I'm using zephyr RTOS.
I'd like to put the cpu System ON Sleep Mode to conserve power.
Then, I'd like to restart the CPU with an interrupt or event from the comparator...
Hi, I'm working on a project, I want nRF51822 can get notification when android phone got a call or email, just like ANCS work with iPhone.
I tried ble_app_alert_notification...
Hello,
Apologies as I'm very new to C and I may be missing something obvious. I have an actual ble Heart Rate device which I wish to connect to my pca10028 (nrf51422_xxAC...
I am try to porting nRF51822 Beacon v1.0.1 F/W for PCA20006 to PCA10001.
I could change GPIO port setting for button and LED.
Now normal beacon mode work fine and success...
We appear to have discovered today that if you do this sequence
sd_power_gpregret_clr(0xFF);
sd_power_gpregret_set(0xA0);
sd_power_gpregret_set(0x0B);
GPREGRET will...
I'm trying to understand the general structure of .h files.
nrf.h contains an #ifdef for NRF52.
I cannot find a #define NRF52 anywhere.
Any help appreciated.
Thanks...
We have our nrf52 working well with our iOS app - almost everything we need is in place. One last item (haha) we've been struggling with is to get the nrf52 to advertise our...
Hi,
I'm connecting to a proximity sensor, IQS263 over TWI interface and having some weird problems.
I'm using the same code I used to connect with the Invensense MPU...
Hi.
We are trying to get nrf52 to work with 1.8v spi master. We are using level sifter with it. However when we connect the nrf52 to level sifter to spi output, the whole...
i am working with nrf24l01 module with PA LNA circuitry for longer distance transmission.When i bought the module i received an antenna along with it which is an SMA antenna...
Hi,
I have read "Measuring Lithium battery voltage with nRF52" posted on 5-23-16 just as a point of reference.
System setup:
In my system the nRF52 is powered (VDD...
Hello,
I need help,
I'am using uvision V5.17, SDK 9.0.0 and SD130.
First problem is solved,
If I don't declare app_pwm_init() in app_pwm.h, the current is 0.4mAh...
Hi, I'm having an issue, when i compare the data received over BLE NUS SERVICE, i want to choose stay connected or disconnect to the device..(if i don't receive the data that...
In my mesh I would like to have some battery powered nodes which will only transmit data and never receive.
Is there a way to disable scanning entirely while using the...
Hi I am using Bluetooth Gatt to read/write, discover services from nRF51822 device. But the behaviour is quiet unpredicatable. I am testing on KIT_KAT 4.4. Sometimes there...
I am trying to get the ble_app_uart project working on a Taiyo Yuden EYSGCNZWY using SDK 11 and the S130 Softdevice. The EYSGCNZWY documentation located here here states that...
