I am Using SPI4 in nrf5340 and I am trying to put SPI in low power mode when not in use. How can I do that?
Here is the code given:
aliases {
displayspi...
I am currently creating and testing a custom board equipped with the nRF9160 and the P822601 antenna. Considering future development, it is expected that another external...
Title: nRF54L05 issue after migrating from NCS 3.0.0 to NCS 3.3.0 with PM static partitions and MCUboot external-flash secondary slot Description: I am migrating a project...
I am currently designing a custom board for my nRF54L15 project and I would like to know if the "Antenna" pin on the nRF54L15 can have a DC path to ground/ground layer of...
I have a nRF54l15dk development board and a custom nRF54L15 board that I am trying to load a Matter Template sample application on. I have created a custom board device tree...
I have observed that when using the ESB protocol at maximum throughput, the measured power consumption decreases as the PHY data rate increases: 4 Mbps consumes less power...
Subject: Connecting LPCOMP CROSS event to TWO DPPI-driven tasks (GPIOTE toggle + TIMER count) simultaneously — only the last-configured one fires
Chip: nRF54L15 SDK: nRF...
I have some BLE traffic that I have sniffed and am displaying in Wireshark. Most of the opcodes (read/write request/response indications/notifications etc.) are parsed/displayed...
I am trying to develop a GATT service on nRF51.
The GATT service measures a few values, and stores them in a characteristic. When the GATT server (phone) requests data...
I am trying to build a device to stream the 9 axis sensor data from the I2C based sensor and then transmit it using BLE UART profile. It is sampled every 3 seconds using app...
I am using an nrf51422 board. I want to update via OTA using ANT+ Dongle. The device information shown in the OTA Updater is parsed from the Bootloader Code. Is there any...
Hello!
I want to connect the MCP9808 with the nrf52832. Therefor I use i2C.
My example on the nrf52832 is the:
<nRF5_SDK_v11_0_0 folder>\examples\ble_peripheral\experimental_ble_app_eddystone...
We're quite interested in producing an nRF52 design based on the solar beacon (great design, and clean software). I appreciate the relative simplicity and manageable BOM cost...
Hello,
I am developing a system that samples 3 independent data using SSADC. since the timing was important in my system, I decided to use PPI to trigger the SSADC.
However...
When using app_timer through scheduler, a break and go will overflow the event queue if a timer is a repeat timer. The effect is that it's not possible to debug.
To work...
Hello all
I am trying to implement hardware flow control for UART.
is there anything else to be done ? I have done the GPIO configurations like this
const app_uart_comm_params_t...
Hi,
I'm trying to migrate from SDK 6.1 to SDK 7.2 on custom board.
In SDK 6.1 everything works fine (SoftDevice v7.1.0), but with SDK 7.2 I get into HardFault Handler...
Hi My project need to transport HRM data by ANT+/BLE. base on ANT_s332_nrf52_0.9.1.alpha.hex and sdk nRF5_SDK_11.0.0_89a8197 platform. We have finished the function. Now we...
Hi all,
I know that there is a field "address type (public/random)" in white list.
When a scanner send scan request to an advertiser with public device address. this...
I have used the nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_proximity\pca10028\s130\armgcc for my project before I had the final PCB. I have tested my code on...
Hello,
I was wondering why I am not getting a theoretical sampling rate as I set them to with a timer.
I am using PPI to trigger a SAADC sampling with the timer to set...
