Hi Sirs
We are planning to use the nRF54LM20A/B together with the nRF21540 FEM in our design, and we have a few technical questions regarding TX power control and FEM...
Hi Nordic Support Team,
We are currently evaluating the nRF54L05 DFU single-slot sample in NCS v3.3.0.
Our question is: Is it technically possible to configure the single...
Hi,
I'm using the published nRF54L15 DK hardware files and noticed something that I don't understand.
On the nPM1300 section of the schematic and PCB:
Pin 20 ( VSYS...
we are developing solutions with PMIC type=PM1300, we eager to know the internal LDOs PSRR.
i have read 171 page of PM1300 datasheet, but cannot find PSRR data or the PSRR...
nRF54L15 PDM clock runs at ~1/32 of expected (PCLK1M instead of PCLK32M) on a custom board - works on DK
Summary
On a custom nRF54L15 board, the PDM peripheral clock ...
HI
I am currently using the nRF54L15 chip with NCS 3.2.1, carrying out secondary development based on the periodic_sync_conn sample project. I intend to adjust the transmit...
While configuring a scene, the blind device is not visible in the scene settings screen, so it is not possible to set or save the blind position as part of the scene.
Steps...
We have created Thread Network include Leader, router and end devicewitch nRF SDK v2.5.0 on nRF 52840
We found the Thread connect will offline after 15 minute and not reconnect...
This is a higher-level question because I'm having difficulty finding concise and clear practices for this sort of thing. I don't want to go implementing something subpar...
Hi folks,
I'm making an application which needs to transmit a few kB of config data (for a configuration utility), and I was hoping to do it via UART.
To that end, I loaded...
I am working on specialized PCB's for my job, and we are trying to capture modem traces for our devices. Via JTag, I have serial access to pins P0.05 (TX) and P0.06 (RX) of...
Hi All
I m developing a project in nref9160, in GNSS part, I need to use PGPS, but can I control the checking in nrfCloud? sometimes it go to download PGPS and make GPS...
Dear Nordic Developer Zone,
I am working on MAX30003 ECG ( https://datasheets.maximintegrated.com/en/ds/MAX30003.pdf ) with Nrf52840-DK. My sensor is work on the 32.768kHz...
Hi,
I have been having quite a lot of issues around connectivity and my device, all of which at this point has stemmed from MNO blocking activity from MVNO's ( here and...
I tried adding DFU capability to the broadcast_audio_sink sample. At first i copied the whole sample code to a different directory and opened that folder in VSCode which has...
We are running into an issue of stability with our LTE connection. Our nRF9160 makes a call every 5 minutes to our backend. On start-up, the device connects and starts making...
Hi,
I am working on mesh network. i need to control 10 nodes in the mesh network with having one main node. I have taken the light switch sample as an example.
The process...
Hello,
We are trying to use nrf5340 and W25Q128JV ( https://www.winbond.com/resource-files/W25Q128JV%20RevI%2008232021%20Plus.pdf ) nor flash on our own designed card. I...
Hello,
We are trying to get the XIP example working with a custom nrf5340 board with the mx25l25645g memory chip. Using VSCode, 2.7.0 toolchain, 2.7.0 sdk
The project...
Hello,
nRF connect sdk extension v2024.9.87 stopped working for building Zephyr apps (HWMv2). Previous version worked fine. Extension crashes loading project
The issue...
Hello,
Not sure if this is the right place to report a bug, but I couldn't find anywhere else.
I have an issue on nRFCloud when looking at the messages in the terminal...
