Hello,
I have tried twice to request for SUPL license for getting A-GPS working but it has been denied both of the times. I think first time it got denied due to mismatch...
Hi Nordic Team,
The atomic fifo implementation is based on armv7-M, right now I want to port it into cortex-A processor, I made some changes to get it compiled without...
Hi,
Kit:nrf5340
Can you please tell me if there is any example in nrf connect SDK v1.5.0 related to data transfer concepts.
Is ble controller will be enabled during...
I'm was testing the gsp sample in samples/nrf9160/gps. It runs fine on my nRF9160DK and reports NMEA messages. However, when i ran it on my custom board, it failed in setup_modem...
Hi,
I'm attempting to obtain sensor values for a project to be completed less than a week from now and I have not yet started programming so any help would be greatly appreciated...
Hi
I am using nrf52832,SDK version: SDK : RF5_SDK_17.0.2 .
USE CASE:We have two central and one peripheral.We need to control two central with one peripheral(REMOTE...
Dear All,
I need your help to clarify some LE Audio protocol related concepts.
For the BIS use cases. When the PC pause the playback, after that, are there any ISO packets...
The MCUboot, Slot0, and Slot1 flash partitions are defined in the board file. E.g., nrf52840dk_nrf52840.dts has boot_partition at 0 with length 0xC000, slot0_partition at...
OS: Windows 10
NCS: 2.4.2 We are evaluating adding the APDS9960 to our existing nRF52833 based application, but can not get the APDS9960 functioning. We are interfacing...
Hi,
in the PCB circuit I marked in the pictures, it seems that vias have been added to the marked areas on the pads of the nRF52840. However, PCB manufacturers say that...
Hi, I am relatively new to the Nordic platform and Zephyr RTOS. I am using nRF Connect SDK version 2.6.0 (the VS Code extension on Windows 11) with the nRF52840DK. I was wondering...
Hi,
I am designing a two Layer PCB with nRF52840 with PMIC, RTC, Flash. Can anyone from Nordic Review it? especially the RF antenna, I have used the Reference design from...
To verify my Custom antenna design on a PCB . AND VERIFY THE PCB.
https://cart.jlcpcb.com/quote/gerberviewThree/?qs=582f0d800a0c49398584815906f24877_1_0_1_0_0.html&_gl=1...
Hi
We are developing Zephyr projects which are compiling and working fine with Visual Studio Code running on a Windows PC.
Now we want to build the projects on a build...
Hello,
I am wondering where the best place to add a transport layer for DFU is? I have both bootloader examples working, but now i need to add the transport layers. On one...
I am implementing SPI communication between the intanRHD2132 (ADC) and nRF52840.
I need to periodically send commands (READ, WRITE, etc.) to the intanRHD2132 (ADC). To achieve...
Hello,
I am using the nRF52840 as modbus client and experiencing some missing bytes during communication (RTU mode) when using a high baud rate (460800). This tends to happen...
Hello, I have a question about how to get commands generated from a client cluster in a coordinator. I am currently developing a hub to control and retrieve data from home...
Hi
I tried to play an audio convert file by NRF52840 via I2S, but the sound output was like noise (incorrect):
This is my config I2S:
The audio file I am using "Audacity...
Hi,
Before, posting I tried this post below, but it did not work for me. It did not print the manufacturing data.
https://devzone.nordicsemi.com/f/nordic-q-a/84753/scan...
I'm using a custom board based upon the nRF52840. The BME680 chip works fine in another RTOS but the zephyr/nRF connect example is throwing errors.
I added a fair amount...
