Dear Nordic,
it's about USB implementation. We need to add interface string descriptor for ineterface name. Using USBD_STRING_DESCR_DEFINE(primary) I've added that to string...
Hello, I have NRF D 24LU1P 1201FD and NRF F 24LU1P 2136IW. The first one executes all commands, while the second one does not work for writing and erasing. I tried to erase...
Hi! Could you clarify a bit about Bluetooth mesh gateways' implementations. I wonder to know possible ways of Bluetooth mesh gateway implementations. How is it possible right...
Hi everyone.
I catch a terrible issue
When I use nrf52840 and NUS Android app and had for a short time a bad rssi (because of long distance between Android and SoC) and...
Hello
We need to scan for more than 8 devices, so we can't use witelist directly.
We have an idea to use presaved IRK and mac-addresses and use scanning without witelist...
Using v2.8.0-rc2 as v2.7.0 doesn't support the SCRATCH partition.
I am not able to enable BOOT_ECDSA_TINYCRYPT (required for Image Encryption).
I suspect this is because...
Hello
Awhile back I profiled my battery using power up app @ 4C 25C and 45C for a battery between 2.75V and 4.2V battery model is attached in zip.
The profiles themselves...
Dear Nordic Team,
I am working on a project using the nRF7002DK and require guidance on implementing the following functionality:
Acquire data from a sensor using the...
Project (NCS v2.7.0):
We are working on an application that requires time synchronized sampling of sensor data from 4 nRF52840 devices. The sensor data is then streamed...
Hi, We have an application where we need to predict drift between two nRF52833 systems in low power mode running from LFRC (low frequency RC oscillator). Section 5.4.4.4 of...
I am an embedded software engineer and have experience developing BLE devices with nRF5SDK, but this is my first time using Zephyr/NCS.
I am developing a USB dongle (nRF52840...
Hi,
I am developing a product based on the nRF9160 using the LwM2M client. I successfully have this working using PSK, but want to use X509.
I am calling lwm2m_security_set_certificate...
I'm migrating our project with custom boards from NCS 2.6.1 to 2.7.0, and I'm having a number of issues in the vscode extension (v2024.9.87):
The "Create a new board"...
Hi,
We are designing a USB Receiver based off the Nordic Proprietary Radio + ESB.
Do you have any reference designs for a PCB antenna which must be as small as possible...
Hi,
I'm getting an error when building the example temperature that says: Linking 'temperature_pca10040.elf' cannot open output file C:/Users/임선영/Documents/SEGGER Embedded...
I made a custom PCB with the NRF52840-CKAA and the same 8MB flash memory chip as the PCA10056 NRF528040DK
I used the MX25R6435FZAIL0 because the MX25R6435FZNIL0 was not...
Hi,
I'm using the PPI component to generate 8MHz GPIO signal. this signal is an input for power amplifier analog RF transmitter.
While the digital 8MHz signal looks fine...
Hello,
I am designing a LTE-M GNSS Tracker, that should also be able to scan for WIFI APs. I dont need to use LTE and WIFI at the same time, but rather like that:
Connect...
We wanted to share our feedback as we recently went through Zigbee 3.0.1 BDB/cluster certification using the ZBOSS with our end device product. While we were ultimately able...
Hello,
I accidentally programmed BLE firmware onto my Power Profiler Kit 2 (PPK2) , and now the device is not recognized. Here's what happened:
I first opened the NRF...
