Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
we also produced self PWM for ADC wave form testing. when we stop transmission, we will get good waveform out, but when we starting transmission, output waveform shape is...
Dear Support,
I have some troubles with the Evaluation Kit for nRF51822 :
I use the broad as a central role with S120_nrf51822_1.0.0_softdevice.hex and example...
Suppose a nRF9E5 transmitter is set for continuous transmission on a channel.
A nRF9E5 receiver listening on that channel:
finds carrier and sets CD
finds address...
Dear Support team
1) I find that there is a C9 in the nRF52840 reference circuitry for CKAA WLCSP which said that the C9 is not required for Fxx and later as the picture...
Hi,
I am using ppk2 to measure current on a custom board based on particle bsom (nrf52840). I am running ampere meter mode and I can measure some current, but values looks...
Hello Nordic Community,
I installed the serial LTE modem application on my Thingy:91 so that I may use it as a standalone modem. Using minicom on my Linux machine, whenever...
Hi,
I’m quite new to the nRF5 SoC’s and currently facing a problem with USB virtual com port communication using nRF52840 dongle (PCA10059) . I need to get results from...
Our project was previously functional when we were developing using the nrf52840dk_nrf52840 with an overlay to reconfigure for our custom pcba. We created a custom board config...
Hi,
I want to get the VBUS input detection status (USB detected or removed).
I have confirmed that the current state can be known by reading the value of the register...
I needed to rework the memory map, to change the size of the slots to accommodate for a larger foot print. In the programmer, is an "Erase & write" with the hex file sufficient...
Currently the CAF Bluetooth LE advertising module only uses static advertisement data in ble_adv_def.h
Would it be possible to add an interface for setting manufacturer...
Hi support,
We have a product that successfully utilizes DFU and is currently in production. However, we have been seeing a couple units that failed DFU but can still...
Hello all,
I'm trying to send SPI signal from nRF52-DK to other circuit component.
nRF52 doesn't receive data, and send 16 bit data at one transfer.
I want to send data...
Developing on nrf9160 using NCS 2.1.2 and MFW 1.3.3, is there any sort of Hard Fault detection and handler besides the k_sys_fatal_error_handler hook in lib/fatal_error/fatal_error...
Hello,
I recently ordered a Thingy:53.
The first time I turned it on, I successfully tried the Edge Impulse app, and updated the Thingy:53 network and app firmware via...
Hi, my slave will send 55 bytes to SPIM, if I check slave data when SPIM received all data, and it will spend 1.8ms, I think its long.
Can I check data when SPIM starts...
Dear Nordic team, We are using the nRF connect SDK version 2.1.2. Our prototype uses the nrf52840dk board and the KScan application template. However, when directly trying...
Hi,
Want to update the linker script as below in segger embedded studio? How to add this using flash_placement.xml. //update your linker script (.ld file) to expose information...
