I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hi all,
I have a board based on an nRF52832. At the moment I program it through the nRF52 Dev-kit (with the debug out connector) as my board doesn't have any debugger...
I'm a complete idiot when it comes to Nordic, this is literally my first time experience with any Nordic chips. I have a little experience programming ESP32-s3 chips, and...
Im working on a windows 11 Pro (OS Build 22000.1219) with a NRF52 development kit which has a NRF52832 chip set. The board is PCA10040 3.0.0. The device does not communicate...
Hi,
I run the sample zephyr/samples/bluetooth/periodic_adv on 5340, if the controller selected software-base ( CONFIG_BT_LL_SW_SPLIT ), the sample work well; if BT controller...
Hello,
Currently we're working on improving our DALI driver on the nRF52832 chip, because we've experienced issues with transmitting DALI bits with the correct timing. The...
Hello everyone,
I have been trying to get the nRF9160 DK connected to Edge Impulse Platform but it is not possible. i have been following this viedo Connecting nRF9160 DK...
Hello,
I have understood that the pc-ble-driver library is currently in maintenance mode[1] and not getting new features anymore.
We are using pc-ble-driver-py library...
Hello Nordic support,
I am planning to develop an application that will either use Zigbee protocol or BLE protocol. The protocol to be used is determined at startup by reading...
Hi all!
SPI3 Slave project is not built - error:
identifier "__device_dts_ord_DT_N_S_soc_S_peripheral_50000000_S_spi_c000_P_cs_gpios_IDX_0_PH_ORD" not determined
C:\ncs...
Hi,
I want to measure CO2 in different locations using two similar CO2 sensor ( MiCS-VZ-89TE). I can communicate with the sensor over I2C0.
But because two sensors have...
We are facing an issue in nrf52840 (SDK 15). Our hardware uses timer, SPI, USB, FLASH and uDMA. implemented watchdog timer and its working fine as well intented. But in some...
Hi I hope you can help me with this.
I'm using a nrf52833. When I build I see Flash usage of 278044 B.
Regions Size 512KB.
My custom board has this in the Flash0 settion...
