I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
On the nRF52840 using ncs/zephyr v2.6.1, how can I explicitly configure the Coded PHY scheme (selecting either S=2 or S=8) for BLE Extended Advertising? Please provide the...
I tried to fully replicate the example from DevAcademy ( academy.nordicsemi.com/.../) for my project, and added a button and an LED in the overlay. However, once SB_CONFIG_BOOTLOADER_MCUBOOT...
Hello,
We need to interface the nRF54L15 with a 3-wires SPI slave (which uses one single bidirectional pin for MOSI and MISO).
I see two options here:
1. Connect the...
Issue
On the nrf54lm20 using DTLS with MbedTLS, MbedTLS's heap can be exhausted. This will result in a TLS handshake error. When this issue happens MbedTLS does not catch...
Hey,
I have a question regarding the watchdog in a low power application with dynamic sleep times of e.g. 1mim/10mim/1h. In the docs of nrf9160 and also nrf9151 it says...
Hey Nordic support, We want to perform EMC tests on the DECT NR+ for our product and need a continuous wave or tx tone sample for testing. I found the DECT NR+ shell sample...
I mean like when ever i click pristine build in the vs code i am getting this below error " Unable to build: SDK not found. Ensure that a valid SDK is used for the build configuration...
Hi,
We are using the NRF9151 with AT commands to replace our SIMCOM modems.
We would like to write the SIM profile data to the modem via AT commands just like SIMCOM...
Trying to config TDM SCK for: Master, 4 channels, 24 or 32 bits, 16 KHz...doing the math yields 1.536 or 2.048 MHz for SCK. I have 24 MHz or 32 MHz available as possible clock...
Hello, I have a question regarding external flash erase via `nrfutil` command line tool. Does the `nrfutil device` command support doing a qspi erase with custom qspi commands...
Hello,
There is a minor issue identifying a sysbuild configuration if the initial generate and build fails.
Steps to repro:
- add a kconfig that doesn't exist in...
In the past, I've been told I can bypass a lot of the Zephyr nonsense and use the HAL layers of the nRF Connect SDK directly. So if I want to use what was called nrfx_twim_xfer...
Hello,
I noticed the Audio application explicitly states that WAV sample rates other than 48kHz is not supported.
Is there any risk to modifying the code to support other...
