I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
I currently use an NRF52810 to write a firmware in an external flash, then an STM32 will read this firmware and download it in its internal flash. The communication between...
Hello,
I tried to read the value from bq4050 on smbus.
I had good results but I got wrong value randomly as following.
The last marked value is temperature from DAStatus2Reg...
Hello, I am developing a custom firmware for NRF52832 controller. I have develop power saving mode using power manage function. Also I have enabled interrupt inside code and...
hi,In SAADC sampling, the upper limit and lower limit of sampling results are set. Interrupt events are generated only when they are less than the lower limit or greater than...
Hey Devzone
Running into an interesting issue with the .zip files on http://developer.nordicsemi.com/.pc-tools/toolchain/ . When I try to download in browser they fail....
Hi
I am using nrf51422 (on the DK) with S130, SDK12, functioning as a central, reading multiple peripherals (which I also programmed),
Some of those peripherals have manufacturer...
Hello, With reference to Case ID: 278209, I wanted to include a driver file, for which I was suggested to add the label/variable "zephyr_library_include_directories(.)" in...
Hi,
I have a strange problem.
When I connect the jlink and battery power on board at the same time,and download the application, it works normally. But when I disconnect...
Good morning.
I have a custom board with softdevice 132 and sdk 15.0.3 where I have configured pin P0.16 and P0.17 for uart (rx, tx). I have read in other posts/problems...
I have written BTLE code that works on the nRF52840 DK using SoftDevice s140. I have ported this code to work on the nRF51 DK and nrf51822 MCU using SoftDevice s130. I use...
Hi all:
on my project,i set
define NRF_SDH_BLE_PERIPHERAL_LINK_COUNT 1
define NRF_SDH_BLE_CENTRAL_LINK_COUNT 6
on my peripheral , i need mtu = 185
on my central...
The application of a device is developed based on ncs1.3.0, now the SDK version is upgraded, the firmware function is developed based on ncs1.5.1, and a problem is found,...
Hello,
I'm in an aging manufacturing space and would like to utilize your sensors, but im concerned the pillars and walls will prevent data from being sent. I read the...
Hello,
I am using Nrf5340 with “Direct test mode” example.
I try to make my nrf5340 kits to be an AoD receiver under the DTM.
Now,I am able to run the example code to...
