I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi,
Is that possible to run the radio_test_example (\nRF51 SDK_v5.2.0.39364\Nordic\nrf51822\Board\nrf6310\radio_test_example) on the nRF51822EK? If yes, what modifications...
Hello everyone, I am starting with the NRF52840 dongle. I intend to use it for a Uni project because I'm gonna use it later for work (new product). Since we're using STM32...
Hi everyone! I'm a beginner with BLE. I'm trying to test Eddystone beacon. I'm successfully run "ble_app_eddystone" example in NRF52 SDK, and I also successful connect to...
We are doing some rapid prototyping using PCA10040 boards. I have a bench-top setup with a PCA10040, and some sensors. We want to place our sensors on an Arduino shield, enclose...
Hi there,
I just found an example, Experimental: BLE Multiperipheral Application, https://www.nordicsemi.com/DocLib/Content/SDK_Doc/nRF5_SDK/v15-2-0/ble_sdk_app_multiperipheral...
Hello there,
I have a decent amount of experience using arduino IDE and the arduino micro-controllers to generate PWM signals, but wanted to create an BLE app using the...
Hi
I have sd+dfu uploaded and can download app through dfu with no issues. But if I make any change to the app and try to upload app using Keil uVision then nrf52832 not...
HI,
When I use the SAADC example, I found that the data collected during the simultaneous 8-channel acquisition has abnormal data on both channels。
I've ported the SAADC...
I am working on creating a mesh network consisting of sensors and output devices.
I am using the serial example with interactive_pyaci to provision the network from a PC...
Hello,
I'm new in IOT field and in firmware developping area on Nordic SIPs, microcontrollers, but I'm experience in firmware developping area on STM32 microcontrollers...
Hello,
I'm using nRF SDK v15.0.0. I have have added battery service using this online tutorial: https://www.novelbits.io/smart-ble-lightbulb-application-nrf52/ . The code...
I try to eddystone url beacon with advertise every 5 second. I changed
#define APP_CFG_NON_CONN_ADV_INTERVAL_MS 5000
upload code in nrf52832 module I used NRF connect...
Dear Sir,
I am working with SDK15, nrf52832 and softdevice s 132.
I am using ble_app_template with slight modifications.
Now it will advertise for a duration of 10...
