I'm trying to use the ADC and internal reference to measure battery voltage on the nrf51422, while S210 is enabled.
From the example nrf51-ble-app-temp-master, I found...
I have Nokia Lumia 630 and it works well with nRF51822-EK but only with SDK nrf51822_v5.1.0.36092 and SoftDevice 6.0.0. Now I decided to try DFU OTA. I programmed bootloader...
Hello,
I found that there is a multiprotocol demo in folder Board\nrf6310\s110\experimental\ble_app_multiactivity_beacon,then I found it can implement concurrent connected...
Dear Sir
We got the problem on DFU upload firmware, it always failed in second DFU . We must unpair the device at iOS setting panel. Before next DFU.
Here is the log data...
Hi All,
My requirement is to read the data from nRF51822 device that is connected to a bluetooth and bluetooth is connected to a system using a .Net application.
I have...
Hi everyone,
I'm using the nRF51822 (pca10000 Dongle + pca10005).
My plan is to send one byte over the radio.
I tried to use the SDK-Example as a template but it's...
Hi everyone,
I am currently trying to flash the MDBT50Q-DB-40 demo board from Raytac but I'm running into some issues with flashing it. I have both referenced the setup...
I want to develop it in visual study code. I have a few problems right now
1. The left nrf icon in the attached image continues to disappear. Whenever it disappears, if...
I can get certain MCUboot features working for the Lesson 8 test program. However, these features don't work when I try to port them over to a fully fledged project. I think...
Hi
This is my first project to make my custom PCB.
I have a question about how can I uploaded my code with segger embedded studio by using nrf52840 dk?
For the hardware...
Hi,
I've create an v2.4.0 SLM application in VS Code by copy from sample, and I am trying to enable trace function for cellular monitor tool app, in order to LOG the packets...
During our evaluation of MQTT, we observed that if we send data every five minutes, the server stops receiving it. We currently believe this is related to CG-NAT, which drops...
Hi I am getting fatal errors when building most of the exercises in the Wifi Fundamental course. I have attached terminal output from building the wififund_less4_exer1_solution...
I have code developed for the nRF52832 based on the Zephyr RTOS. If I switch to the nRF5340 with Zephyr RTOS, would it be possible to develop by simply uploading the additional...
Dear all:
I have built a project(ex: matter bulb) in Nordic SDK, the generated load is zephyr.hex which size is about 2345kb ;
Then I open nRF Connect Programmer, and...
I'm attempting to get our wearable remote to interact with a GoPro using their API and am getting the error in the subject line when attempting to start scanning. I've checked...
I am working on scanning and connecting to an iPhone device in NRF52840dk, but I am not able to receive my iPhone while scanning. If there are any different ways, please let...
Hello!
Looking for some guidance on how I should start debugging an issue I'm experiencing trying to get the Zephyr fdc2x1x sample code running on a custom PCB that uses...
Hi everyone,
I am working with the nRF SDK v2.0.4 for VsCode and with the nRF52840 DK.
I want to develop an application that transfer in real time the data collected...
I'm essentially building a BLE to UART gateway to allow our microcontroller device to talk to our apps. The BLE section is the nRF52840 and I'm trying to simply use it to...
I am trying to install the nrf connect SDK on my Macbook M3 Pro. But i am unable to do so. Neither VSCode extension nor the Toolchain manager works for me.
Clicking install...
